2014-2019 Hiace · Service Manual ENGINE

P064C Glow Plug Control Module

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

P064C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (2 trip detection logic).
Glow plug controller
P066B 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 1 glow plug assembly
  3. Short in No. 1 glow plug circuit
P066D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 2 glow plug assembly
  3. Short in No. 2 glow plug circuit
P066F 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 3 glow plug assembly
  3. Short in No. 3 glow plug circuit
P067B 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 4 glow plug assembly
  3. Short in No. 4 glow plug circuit
P0671 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 1 glow plug assembly
  3. Open in No. 1 glow plug circuit
P0672 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 2 glow plug assembly
  3. Open in No. 2 glow plug circuit
P0673 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 3 glow plug assembly
  3. Open in No. 3 glow plug circuit
P0674 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 4 glow plug assembly
  3. Open in No. 4 glow plug circuit
P166F 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. Open or short in glow plug circuit

WIRING DIAGRAM

Refer to DTC P052F (Click here)

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0671, P0672, P0673 and/or P0674 is output
    A
    DTC P066B, P066D, P066F and/or P067B is output
    B
    DTC P064C and/or P166F is output
    C



B
Go to step 8

C
Go to step 13
A


2. CHECK GLOW PLUG CONTROLLER

  1. A241159E16
    Disconnect the glow plug controller connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B64-1(BATT) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.



NG
Go to step 17
OK


3. CHECK HARNESS AND CONNECTOR

  1. Disconnect connectors of the glow plug controller.A348991E03

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B66-1 (GL1) - No. 1 glow plug connector terminal 1
    Always
    Below 1 Ω
    B66-2 (GL2) - No. 1 glow plug connector terminal 2
    Always
    Below 1 Ω
    B65-1 (GL3) - No. 1 glow plug connector terminal 3
    Always
    Below 1 Ω
    B65-2 (GL4) - No. 1 glow plug connector terminal 4
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 1 Glow Plug Connector
    -
    -
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)
    *b
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 glow plug connector.



NG
Go to step 6
OK


4. INSPECT GLOW PLUG ASSEMBLY
  1. Clear the DTCs (Click here).

  1. Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Same DTCs (that have been erased)
    A
    Other DTCs
    B

    HINT:
    Check for DTCs in check mode.



A
Go to step 14
B


5. REPLACE GLOW PLUG ASSEMBLY
  1. Replace the glow plug assembly (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END

8. CHECK HARNESS AND CONNECTOR

  1. Disconnect connectors of the glow plug controller.A348991E03

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B66-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground
    Always
    Below 1 Ω
    B66-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground
    Always
    Below 1 Ω
    B65-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground
    Always
    Below 1 Ω
    B65-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 1 Glow Plug Connector
    -
    -
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)
    *b
    Front view of wire harness connector
    (to Glow Plug Controller)

    HINT:
    Make sure that there are no short circuits to the battery.

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 glow plug connector.



NG
Go to step 10
OK


9. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here).



NEXT
Go to step 11
10. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.

    OK:
    No DTC is output.

    HINT:
    Check for DTCs in check mode.



NG
Go to step 12
OK

END

12. REPLACE GLOW PLUG ASSEMBLY
  1. Replace the glow plug assembly (Click here).



NEXT
Go to step 16
13. CHECK HARNESS AND CONNECTOR

  1. Disconnect connectors of the glow plug controller.A348991E03

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B66-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground
    Always
    Below 1 Ω
    B66-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground
    Always
    Below 1 Ω
    B65-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground
    Always
    Below 1 Ω
    B65-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 1 Glow Plug Connector
    -
    -
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)
    *b
    Front view of wire harness connector
    (to Glow Plug Controller)

    HINT:
    Make sure that there are no short circuits to the battery.

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 glow plug connector.



NG
Go to step 15
OK


14. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here).



NEXT
Go to step 16
15. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


16. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END

17. INSPECT GLOW RELAY
  1. Inspect the GLOW relay (Click here).



NG
REPLACE GLOW RELAY
OK


18. CHECK HARNESS AND CONNECTOR
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Remove the GLOW relay assembly.

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Disconnect connectors of the glow plug controller.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GLOW relay terminal 5 - Battery positive terminal
    Always
    Below 1 Ω
    GLOW relay terminal 1 - Body ground
    Always
    Below 1 Ω
    GLOW relay terminal 3 - B64-1 (BATT)
    Always
    Below 1 Ω
    GLOW relay terminal 2 - B97-27 (GREL)
    Always
    Below 1 Ω
    GLOW relay terminal 5 or Battery positive terminal - Body ground and other terminals
    Always
    10 kΩ or higher
    GLOW relay terminal 3 or B64-1 (BATT) - Body ground and other terminals
    Always
    10 kΩ or higher
    GLOW relay terminal 2 or B97-27 (GREL) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0630 VIN not Programmed or Mismatch - ECM / PCM (from Jan 2017)P0724 Brake Switch "B" Circuit High (from Jan 2017) →