Home › Drivetrain › AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GD-FTV) › 2019.02–2019.06
RM35X0E _52 Drivetrain _078741 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0382313 AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV) A

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV)  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C370661C01
0.708,2.802 0.885,2.802 0.885,2.802 1.063,2.302 true 0.542,0.417 0.719,0.417 0.719,0.417 0.99,0.927 true 2.271,1.021 2.365,0.854 2.365,0.854 2.479,0.854 true 2.698,1.74 2.938,2.063 2.938,2.063 3.052,2.063 true 2.177,1.417 2.323,1.417 2.323,1.417 2.438,1.5 true 2.615,3 2.76,3 2.76,3 2.917,2.896 true 1.99,1.323 2.302,1.479 0.313,0.156 10 false *1 2.448,2.917 2.76,3.073 0.313,0.156 10 false *2 0.365,0.313 0.677,0.469 0.313,0.156 10 false *a 3.073,1.552 3.271,1.729 0.198,0.177 10 true (b) 2.49,0.75 2.698,0.906 0.208,0.156 10 false *a 3.083,0.99 3.292,1.188 0.208,0.198 10 true (a) 0.531,2.729 0.844,2.885 0.313,0.156 10 false *b 3.115,1.99 3.271,2.167 0.156,0.177 10 false *b 2.417,0.427 2.625,0.583 0.208,0.156 10 false (A)
*1 Flywheel
*2 Straightedge
*a Engine Assembly Surface
*b Pump impeller drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*a) and the torque converter assembly contact surface of the pump impeller drive plate (*b).

Measurement Method:

(a) - (b) = (A)



b.
C324536C01
0.938,0.521 0.469,0.167 0.469,0.167 1.021,0.302 true 0.281,0.052 0.594,0.208 0.313,0.156 10 false *a
*a Matchmark


Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



c.
C324537C01
3.177,1.031 3.396,1.25 0.219,0.219 10 false *1
*1 Front Oil Pump Oil Seal


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




d.
C416517C01
3.177,1.042 3.375,1.24 0.198,0.198 10 false *1
*1 Front Oil Pump Oil Seal


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




e.
C324539N01
2.854,0.469 3.01,0.667 0.156,0.198 10 false B

Using a vernier caliper and straightedge, measure the dimension shown in the illustration and check that the dimension is more than the dimension (A), which was measured in the previous step.

Standard Distance:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 33829E 2.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.

Install the transmission control cable bracket to the automatic transmission assembly with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the automatic transmission assembly with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C274145C04
1.042,1.063 1.385,1.063 true 1.75,1.167 2.01,1.594 2.01,1.594 2.167,1.594 true 0.875,0.969 1.188,1.167 0.313,0.198 10 false *1 2.229,1.49 2.542,1.688 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



b.
C414543C01
0,0 0,0 false
V100135

Knock Pin
V100136

Bolt


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

While keeping the engine assembly and automatic transmission assembly horizontal, align the 2 knock pins with the holes in the automatic transmission assembly and install the 5 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

·

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.




Hide 82121 5.CONNECT ENGINE WIRE

a.

Connect the engine wire and attach the 4 wire harness clamps to the 2 wire harness clamp brackets.

C414540C01
0,0 0,0 false
V113147

Push Up - -



b.

Connect the park/neutral position switch assembly connector, transmission wire connector and 2 transmission revolution sensor connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



Hide 82122A 6.CONNECT NO. 2 ENGINE WIRE

a.

Attach the 3 clamps.


b.

Install the bolt to the automatic transmission assembly.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12380 7.INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY

a.
C411037C01
0,0 0,0 false
V100136

Front of the Vehicle


Install the rear engine mounting insulator assembly to the automatic transmission assembly with the 4 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 57209B 8.INSTALL REAR ENGINE MOUNTING MEMBER SUB-ASSEMBLY

a.
C411022C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the rear engine mounting member sub-assembly to the vehicle body with the 4 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


b.

Install the 3 nuts to the rear engine mounting member sub-assembly.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

w/ Cover:

Install the step plate cover RH.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


Hide 9.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the remaining 5 silver colored bolts.



Hide 11356A 10.INSTALL NO. 2 REAR END PLATE

a.
C413184C01
0,0 0,0 false
V113147

Install


Install the No. 2 rear end plate to the automatic transmission assembly.


Hide 12584 11.INSTALL NO. 4 CYLINDER BLOCK INSULATOR

a.

Install the No. 4 cylinder block insulator to the engine assembly.


Hide 33119B 12.INSTALL STIFFENER PLATE LH (ATM)

a.

Temporarily install the stiffener plate LH (ATM) to the automatic transmission assembly and engine assembly with the 4 bolts.


b.

Tighten the 4 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 33118B 13.INSTALL STIFFENER PLATE RH (ATM)

a.

Temporarily install the stiffener plate RH (ATM) and wire harness clamp bracket to the automatic transmission assembly and engine assembly with the 4 bolts.


b.

Tighten the 4 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 32921 14.CONNECT NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE

Hide 3516A 15.INSTALL TRANSMISSION OIL PAN HEAT INSULATOR

a.

Install the transmission oil pan heat insulator to the automatic transmission assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 35979B 16.INSTALL TRANSMISSION INSULATOR RH

a.

Install the transmission insulator RH to the automatic transmission assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 33820B 17.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C411038N03
2.125,1.771 2.292,1.938 0.167,0.167 10 true N

Turn the control shaft lever LH clockwise until it stops, and then return the control shaft lever counterclockwise 2 notches to N.


b.

Move the shift lever to N, and with the cable end lightly pushed toward the front of the vehicle, connect the transmission control cable assembly to the transmission control shaft lever LH with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

HINT:

Tighten the nut with no slack in the transmission control cable assembly.



c.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.


Hide 17410 19.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 26.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 27. RESET MEMORY

NOTICE:

If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>INITIALIZATION