Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR VALVE (w/ EGR Cooler) › 2019.02–2019.06
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384171 EGR VALVE(w/ EGR Cooler) A

1GD-FTV EMISSION CONTROL  EGR VALVE(w/ EGR Cooler)  INSTALLATION  


PROCEDURE

Hide 25630 1.INSTALL NO. 2 EGR VALVE ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install the 4 stud bolts to the No. 2 EGR valve assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install a new gasket and the No. 2 EGR valve assembly to the No. 1 EGR cooler with the 4 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 25624 2.INSTALL EGR VALVE ADAPTER

a.

Install a new gasket and the EGR valve adapter to the No. 2 EGR valve assembly with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 3.INSTALL NO. 1 EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY

a.

Temporarily install the No. 1 EGR cooler with No. 2 EGR valve assembly to the intake manifold with the 4 bolts.


b.
A442603C02
0.125,0.156 0.438,0.313 0.313,0.156 10 true *A 0.156,2.521 0.469,2.677 0.313,0.156 10 true *B 0.417,0.417 0.583,0.594 0.167,0.177 10 true 4 3.083,0.844 3.25,1.021 0.167,0.177 10 true 3 2.24,1.948 2.406,2.125 0.167,0.177 10 true 2 1.479,2.042 1.646,2.219 0.167,0.177 10 true 1 0.417,2.781 0.583,2.958 0.167,0.177 10 true 4 3.094,3.208 3.26,3.385 0.167,0.177 10 true 3 2.26,4.313 2.427,4.49 0.167,0.177 10 true 2 1.469,4.406 1.635,4.583 0.167,0.177 10 true 1
*A for Single Actuator EGR Bypass Valve
*B for Double Actuator EGR Bypass Valve


Tighten the 4 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Make sure to tighten the bolts in the order.



Hide 25601 4.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and connect the EGR pipe with cooler sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the EGR pipe with cooler sub-assembly to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25601 5.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the No. 1 EGR pipe sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the No. 1 EGR pipe sub-assembly to the vacuum transmitting pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16209 6.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.


c.

Connect the No. 7 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.


Hide 16206B 7.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 3 water by-pass pipe sub-assembly to the No. 1 EGR cooler with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


c.

Attach the clamp and connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 25800 8.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

Install a new gasket and the electric EGR control valve assembly to the No. 2 EGR valve assembly with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


c.

Attach the clamp and connect the connector to the common rail assembly.


Hide 25612 9.INSTALL NO. 2 EGR PIPE

a.

Install 2 new gaskets and the No. 2 EGR pipe to the electric EGR control valve assembly and intake manifold with the 4 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 25625 10.INSTALL EGR VALVE BRACKET

a.

Install the EGR valve bracket to the electric EGR control valve assembly and intake manifold with the bolt and nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 82121 12.CONNECT ENGINE WIRE

a.

Attach the clamp and connect the engine wire to the No. 4 water by-pass pipe sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Attach the 2 clamps and connect the engine wire to the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.


c.

Connect the 2 connectors to the vane pump assembly.


d.

Connect the connector to the sensor wire of the common rail assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


e.

Connect the connector to the glow plug connector.


f.

Connect the connector to the electric EGR control valve assembly.


g.

Connect the 4 connectors to the 4 injector assemblies.


h.

w/ DPF:

i.

Connect the 3 connectors to the 3 exhaust gas temperature sensors.


ii.

Attach the clamp and connect the connector to the differential pressure sensor.



i.

Attach the 3 clamps and connect the engine wire to the 2 wire harness clamp brackets.


j.

w/ DPF:

Connect the connector to the exhaust fuel addition injector assembly.


k.

Connect the connector to the camshaft position sensor.


l.

Attach the clamp and connect the connector to the intake mass air flow meter assembly.


m.

Connect the 2 connectors to the turbocharger sub-assembly.


Hide 23941 13.CONNECT NO. 1 FUEL FILTER PROTECTOR

a.

Connect the No. 1 fuel filter protector to the body.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Attach the clamp and connect the wire harness to the No. 1 fuel filter protector.


c.

Connect the connector to the fuel filter assembly.


Hide 12632 14.INSTALL NO. 2 ENGINE COVER BRACKET

a.

Install the No. 2 engine cover bracket to the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23265C 15.INSTALL GAS FILTER

a.

Attach the clamp and install the gas filter to the gas filter bracket.


b.

Connect the vacuum hose to the intake manifold.


Hide 89421C 16.INSTALL DIESEL TURBO PRESSURE SENSOR

a.

Connect the vacuum hose and install the diesel turbo pressure sensor to the No. 3 water by-pass pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the connector to the diesel turbo pressure sensor.


Hide 16278 17.INSTALL NO. 2 WATER BY-PASS PIPE

a.

Install the No. 2 water by-pass pipe to the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 16 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.


c.

Connect the No. 15 water by-pass hose to the water by-pass pipe, and slide the clamp to secure the hose.


d.

w/ Heater:

Connect the No. 13 water by-pass hose to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.


e.

w/ Viscous Heater:

Connect the water by-pass hose sub-assembly to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.


f.

for Laminated EGR Pre-cooler:

Attach the clamp, connect the No. 18 water by-pass hose to the EGR pipe with cooler sub-assembly, and slide the clamp to secure the hose.


Hide 87209 18.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)

a.

w/o Rear Heater:

Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.


b.

w/ Rear Heater:

i.

Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.


ii.

Connect the 2 water hose sub-assemblies to the water pipe, and slide the 2 clamps to secure the hoses.



Hide 26100G 19.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 55701J 20.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 85110 21.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 22.ADD ENGINE COOLANT