Home › Vehicle Interior › HEATING / AIR CONDITIONING › PTC HEATER ASSEMBLY › 2019.02–2019.06
RM35X0E _58 Vehicle Interior _079316 HEATING / AIR CONDITIONING _0384885 PTC HEATER ASSEMBLY A

HEATING / AIR CONDITIONING  PTC HEATER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the PTC heater assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement part or procedure Necessary procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Stop and start system

Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67912A 3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55011A 6.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55318C 7.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55641 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 53601 9.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 77306 10.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Hide 55432D 11.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55044C 12.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55433B 13.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 55445B 14.REMOVE INSTRUMENT PANEL FINISH PLATE (w/o Knee Airbag)

Hide 55313 15.REMOVE LOWER INSTRUMENT PANEL LH (w/o Knee Airbag)

Hide 73900 16.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 58810J 17.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box)

Hide 58533C 18.REMOVE CENTER FLOOR CARPET COVER RH

Hide 58534E 19.REMOVE CENTER FLOOR CARPET COVER LH

Hide 55646 20.REMOVE NO. 3 INSTRUMENT PANEL UNDER COVER

Hide 33504F 21.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)

Hide 58840Q 22.REMOVE SHIFTING HOLE COVER ASSEMBLY (for Manual Transmission)

Hide 55405B 23.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 24.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55434B 25.REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55414A 26.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (for Semi-trim)

Hide 55413D 27.REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL

Hide 55306A 29.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 30.REMOVE TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY (for Automatic Transmission)

Hide 87710G 31.REMOVE QUICK HEATER ASSEMBLY

a.
E415413C01
0,0 0,0 false
V100135

Screw
V100136

Connector
V113147

Remove in this Direction


Detach the clamp and disconnect the 2 connectors.


b.

Remove the screw and quick heater assembly as shown in the illustration.

NOTICE:
E382588C01
0.677,1.646 0.677,1 true 0.188,1.646 0.188,0.896 0.188,0.896 0.5,0.896 true 0.604,1.667 0.917,1.865 0.313,0.198 10 false *a 0.115,1.667 0.427,1.865 0.313,0.198 10 false *b
*a Element
*b Fin


·

Do not hold the quick heater assembly by the element or fin. Also, do not damage the quick heater assembly.

·

Foul odors may occur due to oil adhering to the quick heater assembly.