Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
Use the same procedure described for the LH side.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
75986
1.INSTALL FRONT DOOR STRIPE LH (w/ Stripe Tape)
75985F
2.INSTALL FRONT DOOR OUTSIDE STRIPE (w/ Stripe Tape)
75981E
3.INSTALL FRONT FENDER STRIPE (w/ Stripe Tape)
67001A
4.INSTALL FRONT DOOR PANEL CUSHION
Attach the claw and install the front door panel cushion.
Use the same procedure described for the other side.
67837B
5.INSTALL FRONT DOOR DUST PROOF SEAL
Attach the claw and install the front door dust proof seal.
Use the same procedure described for the other side.
67862
6.INSTALL FRONT DOOR WEATHERSTRIP LH
Attach the clip (A).
| *a | Clip (A) | - | - |
Attach the clip and install the front door weatherstrip LH.
68620
7.INSTALL FRONT DOOR CHECK ASSEMBLY LH
When reusing a bolt (B):
Clean the threads of the bolt with non-residue solvent.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
|
Bolt (A) |
|
Bolt (B) |
Install the front door check assembly LH with the 2 bolts (A) and bolt (B).
69760B
8.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH
69720D
9.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
69036A
10.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY LH
69318C
11.INSTALL DOOR LOCK WIRING HARNESS SEAL
When reusing front door lock with motor assembly LH:
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSTALLATION
69040A
12.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH
69202A
13.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly LH.
| *a | Inside |
| *b | Outside |
Attach the guide and install the front door outside handle frame sub-assembly LH as shown in the illustration.
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly LH with the "TORX" screw.
69312
14.INSTALL FRONT DOOR LOCK OPEN ROD LH
69254C
15.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH
Attach the guide and install the front door rear outside handle pad LH.
69252
16.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH
Attach the claw and guide to install the front door front outside handle pad LH.
69503
17.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY LH (w/ Lock Cylinder)
Apply MP grease to the sliding parts of the front door lock cylinder assembly LH.
|
Install in this Direction |
Insert the front door lock cylinder assembly LH to the front door panel assembly LH as shown in the illustration.
Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly LH with the "TORX" screw.
Install the hole plug.
69217E
18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER RH (w/o Lock Cylinder)
|
Install in this Direction |
Attach the claw of the front door outside handle cover RH in the direction indicated by the arrow.
Using a T30 "TORX" socket wrench, install the front door outside handle cover RH with the "TORX" screw.
Install the hole plug.
69220
19.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
|
Install in this Direction |
Install the front door outside handle assembly LH in the direction of the arrow shown in the illustration.
| *1 | Holder |
|
Install in this Direction |
Lower the lever in the direction indicated by the arrow shown in the illustration and attach the claw.
67404F
20.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Attach the guide.
Install the front door rear lower frame sub-assembly LH with the 2 bolts.
68216
21.INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP LH
Install the front door fix window weatherstrip LH to the front door fix window glass LH.
68126
22.INSTALL FRONT DOOR FIX WINDOW GLASS LH
|
Install in this Direction |
Install the front door fix window glass LH with the front door fix window weatherstrip LH as shown in the illustration.
85720C
23.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69820
24.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY LH
Apply MP grease to the sliding parts of the front door window regulator assembly LH.
|
Install in this Direction |
Insert the front door window regulator assembly LH to the service hole as shown in the illustration.
| *a | Temporary Bolt |
Temporarily install the temporary bolt to the front door window regulator assembly LH.
Temporarily install the front door window regulator assembly LH.
Tighten the 2 bolts in the order shown in the illustration.
Do not damage the front door panel with the front door window regulator assembly LH.
|
Bolt |
|
Connector |
Install the front door window regulator assembly LH with the 4 bolts.
Connect the connector.
67834
25.INSTALL FRONT DOOR NO. 2 SERVICE HOLE COVER LH
Attach the claw and install the front door No. 2 service hole cover LH.
68151D
26.CONNECT FRONT DOOR GLASS RUN LH
|
Install in this Direction |
Connect the front door glass run LH as shown in the illustration.
Attach the clip.
68102
27.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
for Driver Side:
Connect the multiplex network master switch assembly connector.
for Front Passenger Side:
Connect the power window regulator switch assembly connector.
Connect the cable to the negative (-) battery terminal.
for 7GR-FKS:
for 1GD-FTV:
Turn the ignition switch to ON.
Move the front door window regulator assembly LH until the installation bolt hole of the front door glass sub-assembly LH can be seen.
|
Install in this Direction |
Temporarily install the front door glass sub-assembly LH to the front door window regulator assembly LH as shown in the illustration.
Be careful not to damage the front door glass sub-assembly LH.
Install the front door glass sub-assembly LH with the 2 bolts.
Move the front door glass sub-assembly LH until the open position.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
for 7GR-FKS:
for 1GD-FTV:
Click hereGeneral>MAINTENANCE>1GD-FTV BATTERY>REMOVAL
After disconnecting the cable from the negative (-) battery terminal, wait for at least 90 seconds to start the operation.
If the airbag deploys for any reason, it may cause a serious accident.
for Driver Side:
Disconnect the multiplex network master switch assembly connector.
for Front Passenger Side:
Disconnect the power window regulator switch assembly connector.
Remove the protective tape.
67402F
28.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Insert the front door front lower frame sub-assembly LH into the front door panel assembly LH in the direction (1) indicated by the arrow shown in the illustration.
Tilt the front door front lower frame sub-assembly LH in the direction (2) indicated by the arrow shown in the illustration and align the bolt holes .
Install the front door front lower frame sub-assembly LH with the 3 bolts.
|
Lift up in this Direction |
Lift up the front door weatherstrip LH as shown in the illustration.
Install the screw.
Install the hole plug.
68151D
29.INSTALL FRONT DOOR GLASS RUN LH
Install the front door glass run LH to the groove in front door front lower frame sub-assembly LH.
68210C
30.INSTALL FRONT DOOR OUTER GLASS WEATHERSTRIP LH
8983AA
31.INSTALL SIDE AIRBAG PRESSURE SENSOR LH (w/ Front Seat Side Airbag)
67838F
32.INSTALL FRONT DOOR NO. 4 SERVICE HOLE COVER LH (w/ Curtain Shield Airbag)
Attach the clip and install the front door No. 4 service hole cover LH with the 4 clips.
67836C
33.INSTALL FRONT DOOR NO. 3 SERVICE HOLE COVER LH (w/ Curtain Shield Airbag)
Attach the claw and install the 3 grommets.
|
Install in this Direction |
Attach the claw and install the front door No. 3 service hole cover LH as shown in the illustration.
Install the 2 clips.
67832
34.INSTALL FRONT DOOR SERVICE HOLE COVER LH
|
Butyl Tape |
Apply new butyl tape to the front door panel assembly LH as shown in the illustration.
| *1 | Front Door Lock Remote Control Cable Assembly LH |
| *2 | Front Door Inside Locking Cable Assembly LH |
|
Install in this Direction |
Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.
| *a | Reference Point |
|
Butyl Tape |
Install the front door service hole cover LH according to the reference points on the front door panel assembly LH.
67626A
35.INSTALL NO. 2 DOOR TRIM BRACKET
Install the No. 2 door trim bracket with the 3 screws.
86160
36.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
67832A
37.INSTALL FRONT DOOR NO. 5 SERVICE HOLE COVER LH
Attach the claw and install the 2 grommets.
Attach the claw and install the front door No. 5 service hole cover LH.
Install the 2 screws.
87940
38.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
68193C
39.INSTALL FRONT DOOR FRONT BELT SEAL LH
|
Install in this Direction |
Attach the grommet and install the front door front belt seal LH as shown in the illustration.
68195B
40.INSTALL FRONT DOOR REAR BELT SEAL LH
|
Install in this Direction |
Install the front door rear belt seal LH as shown in the illustration.
68172A
41.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH
|
Install in this Direction |
Install the front door inner glass weatherstrip LH as shown in the illustration.
69206B
42.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
|
Install in this Direction |
Install the front door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.
Attach the claw and clamp to install the front door inside handle sub-assembly LH.
67602
43.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Attach the clamp and connect the front door lock remote control cable assembly and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH as shown in the illustration.
|
Install in this Direction |
Attach the claw and install the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the clip and install the 3 screws as shown in the illustration.
Remove the protective tape.
84870A
44.INSTALL OUTER MIRROR SWITCH ASSEMBLY (w/ Power Mirror Control System)
84040
45.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)
46.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
| *a | Tether |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Pass the tether through the installation hole of the front door trim board assembly LH and turn the multiplex network master switch assembly with front door upper armrest base panel 90° counterclockwise.
| *A | w/ Power Mirror Control System |
w/ Power Mirror Control System:
Connect the connector.
Connect the connector.
|
Install in this Direction |
Attach the claw, guide and clip to install the multiplex network master switch assembly with front door upper armrest base panel.
|
Install in this Direction |
Attach the claw, guide and clip as shown in the illustration.
Remove the protective tape.
84810
47.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
48.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
| *a | Tether |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Pass the tether through the installation hole of the front door trim board assembly RH and turn the power window regulator switch assembly with front door armrest base panel 90° counterclockwise.
Connect the connector.
|
Install in this Direction |
Attach the claw, guide and clip to install the power window regulator switch assembly with front door armrest base panel.
|
Install in this Direction |
Attach the claw, guide and clip as shown in the illustration.
Remove the protective tape.
69278B
49.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
Attach the claw and install the front door inside handle bezel LH.
50.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
51. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is usel.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
52.INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag)
53. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Front Seat Side Airbag)
54. INITIALIZE POWER WINDOW CONTROL SYSTEM
55. CHECK POWER WINDOW CONTROL SYSTEM
56. CHECK POWER DOOR LOCK CONTROL SYSTEM
57.INSPECT OUTER REAR VIEW MIRROR OPERATION (w/ Power Mirror Control System)