Home › Engine / Hybrid System › 1GD-FTV (COOLING) › THERMOSTAT › 2019.02–2020.05
RM35X0E _51 Engine / Hybrid System _079309 1GD-FTV COOLING _0386770 THERMOSTAT A

1GD-FTV COOLING  THERMOSTAT  INSTALLATION  


PROCEDURE

Hide 16331A 1.INSTALL THERMOSTAT

a.
A341325C01
0.76,1.135 1.01,1.135 false 2.417,1.198 2.667,1.198 false 1.094,0.531 1.406,0.729 0.313,0.198 10 false *a 2.198,0.521 2.51,0.719 0.313,0.198 10 false *b 0.594,1.063 0.906,1.26 0.313,0.198 10 false *1 2.719,1.115 3.031,1.313 0.313,0.198 10 false *1
*1 Gasket
*a CORRECT
*b INCORRECT


Install a new gasket to the thermostat.

NOTICE:

When installing the gasket to the thermostat, be careful not to deform the gasket. Make sure that the groove of the gasket is properly installed to the thermostat as shown in the illustration.



b.
A442845C01
0.771,0.833 1.677,0.833 true 0.615,0.729 0.823,0.917 0.208,0.188 10 true *c 1.615,0.083 1.833,0.281 0.219,0.198 10 true *a 1.313,0.26 1.521,0.427 0.208,0.167 10 true *b 1.927,0.25 2.135,0.417 0.208,0.167 10 true *b
*a Upward
*b 30°
*c Jiggle Valve


Insert the thermostat into the engine water pump assembly with the jiggle valve facing straight upward.

HINT:

The jiggle valve may be set to within 30° on either side of the prescribed position.



Hide 16321 2.INSTALL WATER INLET

a.
A442841

Install the water inlet with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16572D 3.CONNECT NO. 2 RADIATOR HOSE

a.

w/ Viscous Heater:

i.

Connect the No. 2 radiator hose to the water inlet, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 radiator hose paint mark is aligned with the protrusion of the water inlet.



A442847C01
6.063,2.094 5.25,2.198 true 6.5,0.708 6.083,0.594 true 4.438,0.552 4.177,1.219 true 3.365,0.448 3.677,0.604 0.313,0.156 10 false *a 3.531,0.833 3.844,0.99 0.313,0.156 10 false *b 4.396,0.385 4.708,0.542 0.313,0.156 10 false *c 4.073,0.521 4.385,0.677 0.313,0.156 10 false *d 6.615,1.25 6.927,1.406 0.313,0.156 10 false *e 6.417,1.844 6.729,2 0.313,0.156 10 false *f 6.521,0.625 6.729,0.854 0.208,0.229 10 false *g 0.979,0.76 1.115,0.948 0.135,0.188 10 true A 6.781,1.885 7.094,2.042 0.313,0.156 10 false *d 5.073,2.125 5.385,2.281 0.313,0.156 10 false *c
*a View A *b 135°
*c Paint Mark *d Front Side
*e Upper Side *f RH Side
*g Protrusion of the Water Inlet - -




b.

w/o Viscous Heater:

i.

Connect the No. 2 radiator hose to the water inlet, and slide the clip to secure the hose.

NOTICE:
·

Make sure the No. 2 radiator hose is securely inserted to the stopper.

·

Position the clip so that it is 2 to 5 mm (0.0787 to 0.197 in.) away from the end of the water hose.

·

Install so that the No. 2 radiator hose paint mark is aligned with the protrusion of the water inlet.



A442846C01
6.073,2.104 5.26,2.208 true 6.531,0.688 6.083,0.604 true 4.479,0.563 4.167,1.219 true 3.375,0.458 3.688,0.615 0.313,0.156 10 false *a 3.51,0.875 3.823,1.031 0.313,0.156 10 false *b 4.438,0.396 4.75,0.552 0.313,0.156 10 false *c 4.052,0.573 4.365,0.729 0.313,0.156 10 false *d 6.615,1.25 6.927,1.406 0.313,0.156 10 false *e 6.417,1.854 6.729,2.01 0.313,0.156 10 false *f 6.563,0.615 6.771,0.844 0.208,0.229 10 false *g 0.979,0.76 1.115,0.948 0.135,0.188 10 true A 6.781,1.885 7.031,2.052 0.25,0.167 10 false *d 5.094,2.135 5.406,2.292 0.313,0.156 10 false *c
*a View A *b 180°
*c Paint Mark *d Front Side
*e Upper Side *f RH Side
*g Protrusion of the Water Inlet - -




Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System, w/o Viscous Heater)

a.
A442839

Connect the suction hose sub-assembly to the water inlet with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 16207 5.CONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A442838

Connect the No. 2 water by-pass pipe sub-assembly to the engine water pump assembly and water inlet with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 6.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 88359 8.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 16571C 9.INSTALL NO. 1 RADIATOR HOSE

Hide 16470 10.INSTALL RADIATOR RESERVE TANK ASSEMBLY

Hide 44360 12.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 17751 13.INSTALL NO. 1 AIR CLEANER INLET

Hide 53106B 14.INSTALL RADIATOR COVER SUB-ASSEMBLY

Hide 15.ADD ENGINE COOLANT

Hide 51405A 17.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52618 18.INSTALL LOWER FRONT BUMPER ABSORBER

Hide 51406A 19.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)