The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during steering column assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS: Click hereGeneral>MAINTENANCE>7GR-FKS BATTERY>REMOVAL
for 1GD-FTV: Click hereGeneral>MAINTENANCE>1GD-FTV BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
45100
4.REMOVE STEERING WHEEL ASSEMBLY
67912A
5.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH
67914B
6.REMOVE FRONT DOOR SCUFF PLATE LH
62112
7.REMOVE COWL SIDE TRIM BOARD LH
55631A
8.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER
55011A
9.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
55318C
10.REMOVE INSTRUMENT SIDE PANEL LH
55641
11.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER
55432D
12.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
55433B
13.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
73900
14.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
55445B
15.REMOVE INSTRUMENT PANEL FINISH PLATE (w/o Driver Side Knee Airbag)
55313
16.REMOVE LOWER INSTRUMENT PANEL LH (w/o Driver Side Knee Airbag)
45287
17.REMOVE LOWER STEERING COLUMN COVER
Remove the 3 screws.
|
Place Hands Here |
|
Remove in this Direction |
While pressing the push area shown in the illustration to detach the 2 claws, slightly lower the lower steering column cover sub-assembly.
45286B
18.REMOVE UPPER STEERING COLUMN COVER
|
Remove in this Direction |
Detach the claw and separate the upper steering column cover.
Detach the 2 claws and 4 clips to remove the upper steering column cover.
19.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
Using pliers, support the band clamp while loosened.
Detach the claw to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
20.REMOVE FRONT WHEEL LH (for LHD)
21.REMOVE FRONT WHEEL RH (for RHD)
22.DISCONNECT INTERMEDIATE SHAFT ASSEMBLY
Disconnect the intermediate shaft assembly from the rack and pinion power steering gear assembly.
for LHD: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR (for LHD)>REMOVAL
for RHD: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR (for RHD)>REMOVAL
| *a | Matchmark |
Remove the bolt and slide the steering intermediate shaft assembly.
Do not remove the steering intermediate shaft assembly from the steering column assembly.
Put matchmarks on the steering intermediate shaft assembly and steering column assembly.
Remove the steering intermediate shaft assembly from the steering column assembly.
| *a | Matchmark |
Put matchmarks on the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly.
Perform this procedure only when replacement of the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.
Remove the No. 1 steering intermediate shaft assembly from the No. 2 steering intermediate shaft assembly.
Perform this procedure only when replacement of the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.
45250
23.REMOVE STEERING COLUMN ASSEMBLY
Disconnect each connector and disengage each wire harness clamp from the steering column assembly.
Remove the bolt, 2 nuts and steering column assembly.