Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2019.02–2019.06
RM35X0E _55 Steering _079313 STEERING COLUMN _0388799 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

After the column is installed, check the tilt and telescopic operation.

·

If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.

Tighten the nuts and check the tilt operation again.




b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 3.INSTALL INTERMEDIATE SHAFT ASSEMBLY

a.
C413103C01
2.688,0.948 3.104,0.448 3.104,0.448 2.688,0.792 true 3.135,0.333 3.313,0.531 0.177,0.198 10 true *a
*a Matchmark


Align the matchmarks on the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly.

HINT:

Perform this procedure only when replacement of the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.



b.

Install the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly.

HINT:

Perform this procedure only when replacement of the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.



c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:

Perform this procedure only when replacement of the No. 1 steering intermediate shaft assembly and No. 2 steering intermediate shaft assembly is necessary.



d.
C412872C01
1.729,0.531 1.156,0.271 1.156,0.271 1.74,0.458 true 0.938,0.177 1.104,0.365 0.167,0.188 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


e.

Install the steering intermediate shaft assembly to the steering column assembly.


f.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


g.

Connect the steering intermediate shaft assembly to the rack and pinion power steering gear assembly.



Hide 4.INSTALL FRONT WHEEL LH (for LHD)

Hide 5.INSTALL FRONT WHEEL RH (for RHD)

Hide 73900 6.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55313 7.INSTALL LOWER INSTRUMENT PANEL LH (w/o Driver Side Knee Airbag)

Hide 55445B 8.INSTALL INSTRUMENT PANEL FINISH PLATE (w/o Driver Side Knee Airbag)

Hide 55433B 9.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 55432D 10.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55641 11.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER

Hide 55318C 12.INSTALL INSTRUMENT SIDE PANEL LH

Hide 55011A 13.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 55631A 14.INSTALL NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER

Hide 67914B 16.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 67912A 17.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE LH

Hide 18.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C412873

Using pliers, support the band clamp while loosened and set the turn signal switch assembly with spiral cable sub-assembly.


b.
C412874C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly as shown in the illustration.


c.

Tighten the band clamp.


d.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 19.INSTALL UPPER STEERING COLUMN COVER

a.
C412875

Attach the 2 claws and 4 clips to connect the upper steering column cover.


b.
C412876C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the upper steering column cover.


Hide 45024 20.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C412877

Attach the 2 claws to install the lower steering column cover sub-assembly.


b.
C412857

Install the 3 screws.


Hide 21.INSTALL STEERING WHEEL ASSEMBLY

Hide 22.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84306 23.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 24.CHECK STEERING WHEEL CENTER POINT

Hide 45130 25.INSTALL HORN BUTTON ASSEMBLY

Hide 26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 27. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (w/ Airbag System)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART