DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P042000 | Catalyst System Efficiency Below Threshold Bank 1 | During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes.
(2 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class B2 | DTC Stored | SAE Code: P0420 |
| P200200 | Particulate Filter Efficiency Below Threshold Bank 1 | Either condition is met:
(a) PM Sensor Output Current exceeds 12 μA (2 trip detection logic) (b) When driving, the catalyst differential pressure is continuously below the threshold for 7 seconds or more. (2 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly ·
Particulate matter sensor Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class A | DTC Stored | SAE Code: P2002 |
| P245800 | Particulate Filter Regeneration Duration Bank 1 | When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse.
(1 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class B2 | DTC Stored | SAE Code: P2458 |
| P246300 | Particulate Filter Restriction - Soot Accumulation Bank 1 | While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic) |
·
Exhaust manifold converter sub-assembly ·
Exhaust fuel addition injector assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Class B2 | DTC Stored | SAE Code: P2463 |
PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).
| DTC No. | Data List |
|---|---|
| P042000
P200200 P245800 P246300 |
·
Exhaust Fuel Addition F/B Bank 1 ·
Catalyst Differential Pressure Bank 1 ·
Particulate Filter Differential Pressure Bank 1 ·
PM Sensor Output Current |
The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the exhaust manifold converter sub-assembly.
The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL (MIL status: Class B2).
Reduced catalytic converter efficiency is a reduction in performance (crack) detected by the PM monitor used by particulate matter sensor behind the DPF and the DPF differential pressure monitor used by the differential pressure sensor.
PM Monitor:
The ECU uses the particulate matter sensor to monitor the amount of PM behind the DPF after driving.
If the DPF is damaged (cracked) and the PM behind the DPF increases, the particulate matter sensor reacts and outputs a value.
When the output value of the particulate matter sensor exceeds the threshold value, the ECU judges that the DPF is damaged (cracked) and illuminates the MIL.
Differential Pressure Monitor:
The ECU uses the differential pressure sensor and monitors the pressure difference in front and behind the DPF.
If the DPF is damaged (cracked) and the pressure loss in the DPF is decreased, the differential pressure sensor value decreases.
When the output value of the differential pressure sensor falls below the threshold value, the ECU judges that the DPF is damaged (cracked) and illuminates the MIL.
When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL (MIL status: Class B2).
The ECM monitors the PM Accumulation Ratio and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL (MIL status: Class B2).
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P042000 | PM forced regeneration |
| P200200 | ·
After warming the engine, drive the vehicle at approximately 50 km/h for approximately 15 minutes after performing PM forced regeneration. (DTC detection condition (a)) ·
Increase the engine speed to 4000 rpm with no load and maintain it for 10 seconds or more (DTC detection condition (b)) |
| P245800 | PM forced regeneration |
| P246300 | PM forced regeneration |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
After replacing the exhaust manifold converter sub-assembly (DPF catalyst), clear the thermal deterioration data stored in the ECM.
After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
If DTC P245800 or P246300 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-MAIN fuse or battery terminal and waiting for 60 seconds or more before connecting it again.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Record the stored DTC and freeze frame data.
Check Exhaust Fuel Addition F/B Bank 1 and Catalyst Differential Pressure Bank 1 in the freeze frame data.
When the Exhaust Fuel Addition F/B Bank 1 value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.
When the Catalyst Differential Pressure Bank 1 value is more than 0.27, it indicates a high possibility that DPF catalyst is clogged.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P200200 is output | A |
| DTC P244B00 is output at the same time as P246300* | B |
| DTC P042000, P245800 or P246300 is output | C |
| Other relevant DTCs are output | D |
*: When DTC P244B00 is output at the same time as P246300, perform troubleshooting for P244B00.
A
B
C
D
Read the value of "PM Sensor Output Current" in the freeze frame data recorded in Procedure 1.
| Result | Proceed to |
|---|---|
| PM Sensor Output Current is 12 μA or more
(Detected by the PM monitoring function used by the particulate matter sensor) |
A |
| PM Sensor Output Current is less than 12 μA.
(Detected by the pressure difference monitoring function used by the differential pressure sensor.) |
B |
If the PM Sensor Output Current is 12 μA or more, DTC P200200 is output according to detection by the PM monitor function used by the particulate matter sensor.
A
B
Be careful of being burned by exhaust gases during the following inspection.
Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.
| *1 | Air Hose (Downstream) | *2 | Air Hose (Upstream) |
| *3 | No. 2 Vacuum Pipe | *4 | No. 1 Vacuum Pipe |
| *1 | Air Hose |
Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.
Start the engine.
Check if there are exhaust gas pulsations from both air hoses during idling.
Exhaust gas pulsation exists.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Particulate Filter Differential Pressure Bank 1.
| Tester Display |
|---|
| Particulate Filter Differential Pressure Bank 1 |
Check that the differential pressure is as specified below.
Approximately 0 kPa
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Air Hose (Upstream) |
Connect the upstream air hose to the differential pressure sensor.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Particulate Filter Differential Pressure Bank 1.
| Tester Display |
|---|
| Particulate Filter Differential Pressure Bank 1 |
Start the engine.
Run the engine at 4000 rpm with no load for 10 seconds or more.
Check that the differential pressure is as specified below.
| Particulate Filter Differential Pressure Bank 1 | Proceed to |
|---|---|
| 1.5 kPa or higher | A |
| Below 1.5 kPa | B |
B
A
Replace the differential pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the downstream air hose to the differential pressure sensor.
| *1 | Air Hose (Downstream) | - | - |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Particulate Filter Differential Pressure Bank 1.
| Tester Display |
|---|
| Particulate Filter Differential Pressure Bank 1 |
Start the engine.
Run the engine at 4000 rpm with no load for 10 seconds or more.
Check that the differential pressure is as specified below.
| Particulate Filter Differential Pressure Bank 1 | Proceed to |
|---|---|
| -1.5 to 1.5 kPa | A |
| Higher than 1.5 kPa | B |
A
B
It has been determined that the exhaust manifold converter sub-assembly and particulate matter sensor needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly and particulate matter sensor.
This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.
If a vehicle is brought into the workshop and it is determined that the exhaust manifold converter sub-assembly is to be replaced due to DTC P200200, replace the particulate matter sensor at the same time.
If soot is stuck on the particulate matter sensor due to cracking in the DPF catalyst, the particulate matter sensor may react and perform incorrect judgment even after repairing the DPF catalyst back to its normal condition.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace No. 1 vacuum pipe or No. 2 vacuum pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Diagnose relevant DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the procedure [A] 10 times [B].
Check for black smoke emission during the procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| OK |
| NG |
NG
OK
It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.
This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.
| Proceed to |
|---|
| NEXT |
NEXT
Remove the EFI-MAIN fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI-MAIN fuse or reconnect the cable to the battery terminal.
The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.
If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.
Turn the engine switch on (IG).
Turn the engine switch off and wait for 30 seconds or more.
Turn the engine switch on (IG) and wait for 10 seconds or more.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.
If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.
When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.
Enter the following menus: Powertrain / Engine and Transmission / Utility / PM Regenerate Mode.
| Tester Display |
|---|
| PM Regenerate Mode |
Enter PM Regenerate Mode.
Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S2 and DPNR/DPF Status Regeneration (PM).
| Tester Display |
|---|
| Exhaust Temperature B1S2 |
| DPNR/DPF Status Regeneration (PM) |
Check for temperature increases and abnormal white smoke during PM forced regeneration.
PM forced regeneration takes 15 to 40 minutes to finish.
The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio Bank 1" and the vehicle operating conditions.
If the value of "Catalyst Differential Pressure Bank 1" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.
Perform PM forced regeneration control until the display on the multi-information display turns off.
If actions such as depressing the accelerator pedal or operating the DPF switch, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.
PM forced regeneration control is not complete until the display on the multi-information display turns off.
| Result | Proceed to |
|---|---|
| During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and no white smoke is generated | A |
| During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and abnormal white smoke is generated*1 | B |
| Other than above*2 | C |
*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst.
*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.
*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.
A
B
C
It has been determined that the exhaust fuel addition injector assembly and No. 1 injector holder needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly and No. 1 injector holder.
If there is no malfunction in the electrical system, Exhaust Temperature B1S2 is 500°C (932°F) or less even though fuel is injected, and white smoke is not emitted, replace the exhaust fuel addition injector assembly together with the No. 1 injector holder.
| Proceed to |
|---|
| NEXT |
NEXT
It has been determined that the exhaust manifold converter sub-assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter sub-assembly.
If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DPF catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.
| Proceed to |
|---|
| NEXT |
NEXT
Check the fuel injection system.
| Proceed to |
|---|
| NEXT |
NEXT
Check the intake/exhaust system.
| Proceed to |
|---|
| NEXT |
NEXT
Check the after treatment control system.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the following items only when it has been determined necessary based on diagnosis for DTC P042000, P200200, P245800 and P246300.
Replace the exhaust manifold converter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL
Perform the initialization procedure for "DPF catalyst record clear" and "DPF Deterioration Record Clear"
Replace the exhaust fuel addition injector assembly and No. 1 injector holder.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL
If there is no malfunction in the electrical system, Exhaust Temperature B1S2 is 500°C (932°F) or less even though fuel is injected, and white smoke is not emitted, replace the exhaust fuel addition injector assembly together with the No. 1 injector holder.
Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.
Check for DTCs output in step 1.
If DTC 200200 is output, check if it was detected by the PM monitor or differential pressure monitor using the freeze frame data in step 2.
| Result | Proceed to |
|---|---|
| DTC P200200 is output (detected by PM monitor) | A |
| DTC P200200 is output (detected by differential pressure monitor) | B |
| DTC other than DTC P200200 output | C |
A
B
C
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the procedure [A] 10 times [B].
Connect the GTS to the DLC3.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
If DTC P200200 is output, clear it.
If a vehicle is brought into the workshop due to DTC P200200, soot may be stuck in the SCR exhaust pipe. Therefore, clear the soot out of the SCR exhaust pipe by racing the engine.
P200200 may be output again as a result of the particulate matter sensor reacting to the soot stuck in the SCR exhaust pipe being blown out. If P200200 is output again, clear it after racing the engine.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the procedure [A] 10 times [B].
Connect the GTS to the DLC3.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
If DTC P200200 is output, clear it.
If a vehicle is brought into the workshop due to DTC P200200, soot may be stuck in the SCR exhaust pipe. Therefore, clear the soot out of the SCR exhaust pipe by racing the engine.
P200200 may be output again as a result of the particulate matter sensor reacting to the soot stuck in the SCR exhaust pipe being blown out. If P200200 is output again, clear it after racing the engine.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Particulate Filter Differential Pressure Bank 1.
| Tester Display |
|---|
| Particulate Filter Differential Pressure Bank 1 |
Start the engine.
Run the engine at 4000 rpm with no load for 10 seconds or more.
Confirmation that the differential pressure is higher than 1.5 kPa.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PM forced regeneration completes normally.
| Proceed to |
|---|
| NEXT |
NEXT