Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P244B00  Particulate Filter Differential Pressure Too High Bank 1  


DESCRIPTION

Refer to DTC P042000.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>P042000

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P244B00 Particulate Filter Differential Pressure Too High Bank 1 While driving, Catalyst Differential Pressure becomes more than 0.27 for 3 seconds.
(1 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Differential pressure sensor assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Class B2 DTC stored SAE Code: P244B

Related Data List
DTC No. Data List
P244B00
·

Exhaust Fuel Addition F/B Bank 1

·

Catalyst Differential Pressure Bank 1

·

Particulate Filter Differential Pressure Bank 1



MONITOR DESCRIPTION

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL (MIL status: Class B2).

A244057E22
5.979,2.354 5.802,2.354 5.802,2.354 5.573,2.146 true 2.135,3.344 2.375,3.344 2.375,3.344 2.688,2.063 true 4,1.177 4.49,0.458 4.49,0.458 4.708,0.458 true 1.094,3.271 2.188,3.677 1.094,0.406 10 false Stores P244B00 3.531,2.906 4.688,3.198 1.156,0.292 10 false Mass Air Flow 0.135,0.094 2.292,0.323 2.156,0.229 10 false Differential Pressure Malfunction: 0.167,1.635 1.448,2.542 1.281,0.906 10 false Particulate Filter Differential Pressure Bank 1 4.771,0.375 5.969,0.604 1.198,0.229 10 false Clogged with PM 5.76,1.031 7.146,1.458 1.385,0.427 10 false Increases PM amount of DPF catalyst 6.042,2.271 6.969,2.646 0.927,0.375 10 false No PM in DPF catalyst 1.125,0.729 1.51,0.958 0.385,0.229 10 false High 5.604,2.896 5.99,3.125 0.385,0.229 10 false High 1.125,2.563 1.51,2.792 0.385,0.229 10 false Low 1.573,2.906 1.958,3.135 0.385,0.229 10 false Low

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P244B00 Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the exhaust manifold converter sub-assembly (DPF catalyst), clear the thermal deterioration data stored in the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Record the stored DTC and freeze frame data.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

e.

Check Exhaust Fuel Addition F/B Bank 1 and Catalyst Differential Pressure Bank 1 in the freeze frame data.

HINT:
·

When the "Exhaust Fuel Addition F/B Bank 1" value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Pressure Bank 1 value is more than 0.27, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B00)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B00)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456
Result:
Result Proceed to
DTC P244B00 is output A
DTC P244B00 is output at the same time as P246300*
Other relevant DTCs are output B


HINT:

*: When P244B00 is output at the same time as P246300, perform this diagnostic procedure. When DTC P244B00 is not output at the same time as P246300 is output, perform the diagnostic procedure for P042000.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>P042000




A

3.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

B

9.GO TO DTC CHART
3.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine and Transmission > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 456 344

d.

Check the "Particulate Filter Differential Pressure Bank 1" values from idle speed to unloaded maximum engine speed.

Result:
Result Proceed to
"Particulate Filter Differential Pressure Bank 1" increases as engine speed increases from idle speed A
Except above B


A241154E10
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 false Engine Speed (rpm) 0.698,2.99 1.75,3.406 1.052,0.417 10 false Mass Air Flow Sensor (gm/sec) 0.625,4.125 1.698,4.854 1.073,0.729 10 false Particulate Filter Differential Pressure Bank 1 (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 false A 1.771,1.875 1.875,2.156 0.104,0.281 10 false 0 1.781,3.24 1.885,3.521 0.104,0.281 10 false 0 1.792,4.615 1.896,4.896 0.104,0.281 10 false 0 0.677,0.854 1.948,1.24 1.271,0.385 10 false Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 false Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 false Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 false Negative pressure occurs for approx. 1 second.

HINT:

If Particulate Filter Differential Pressure Bank 1 indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

5.CHECK FOR BLACK SMOKE

B

4.CLEAN OR REPLACE AIR HOSE
4.CLEAN OR REPLACE AIR HOSE
a.

Even though it has been determined that the vacuum transmitting hose assembly needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P244B00 before repairing or cleaning it.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)

NG

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Catalyst Differential Pressure Bank 1.

Powertrain > Engine and Transmission > Data List
Tester Display
Catalyst Differential Pressure Bank 1
50003 456 88

d.

Check the value of "Catalyst Differential Pressure Bank 1" at 4000 rpm without load.

Result:
Result Proceed to
"Catalyst Differential Pressure Bank 1" is more than 0.27 A
Except above B




A

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

7.PERFORM PM FORCED REGENERATION
7.PERFORM PM FORCED REGENERATION
a.

Clear the DTC and "Exhaust Fuel Addition FB Bank 1" value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN fuse for 1 minute or more.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


f.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B00 before replacing it.


Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
9.GO TO DTC CHART

NEXT

10.CHECK FUEL INJECTION SYSTEM
10.CHECK FUEL INJECTION SYSTEM

NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B00.


a.

Clean and/or repair the hoses of the differential pressure sensor assembly.


b.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL

NOTICE:

Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).



Result:
Proceed to
NEXT



NEXT

END