The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during No. 3 USB charger socket removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
If the pretensioner has been deployed, replace any damaged parts as necessary.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR SEAT ASSEMBLY
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
67935
4.REMOVE BACK DOOR SCUFF PLATE
73178C
5.REMOVE SEAT BELT ANCHOR COVER CAP (w/ Seat Belt)
73370E
6.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Seat Belt)
73360D
7.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR) (w/ Seat Belt)
Use the same procedure described for the LH side.
67918D
8.REMOVE REAR DOOR SCUFF PLATE LH
Use the same procedure described for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67917C
9.REMOVE REAR DOOR SCUFF PLATE RH
67872A
10.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH
Use the same procedure described for the RH side.
Pull back the No. 1 slide door weatherstrip LH so that the rear quarter trim board assembly LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
67871E
11.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP RH
Pull back the No. 1 slide door weatherstrip RH so that the rear quarter trim board assembly RH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
62640M
12.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY LH
85532D
13.REMOVE NO. 3 USB CHARGER SOCKET (for LH Side)
|
Remove in this Direction |
Detach the claw and remove the No. 3 USB charger socket as shown in the illustration.
62630L
14.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY RH
85532D
15.REMOVE NO. 3 USB CHARGER SOCKET (for RH Side)
|
Remove in this Direction |
Detach the claw and remove the No. 3 USB charger socket as shown in the illustration.