Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Rear Pillar) › from 2019.06
RM35X0E _58 Vehicle Interior _079257 SUPPLEMENTAL RESTRAINT SYSTEMS _0385611 SIDE AIRBAG SENSOR(for Rear Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Rear Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89831C 1.INSTALL NO. 2 SIDE AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

for Van:

i.
B524643

Attach the claw and hold the No. 2 side airbag sensor in place.

NOTICE:
·

If the No. 2 side airbag sensor has been dropped, replace it with a new one.

·

When installing the No. 2 side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.





d.

for Wagon:

i.
B550087

Attach the guide and hold the No. 2 side airbag sensor in place.

NOTICE:
·

If the No. 2 side airbag sensor has been dropped, replace it with a new one.

·

When installing the No. 2 side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.





e.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Tighten the bolt while holding the No. 2 side airbag sensor because the No. 2 side airbag sensor claw is easily damaged.



f.

Check that there is no looseness in the installation parts of the No. 2 side airbag sensor.


g.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:




Hide 89831J 2.INSTALL NO. 4 SIDE AIRBAG SENSOR (for Wagon)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B550088

Attach the guide and hold the No. 4 side airbag sensor in place.

NOTICE:
·

If the No. 4 side airbag sensor has been dropped, replace it with a new one.

·

When installing the No. 4 side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.




d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Tighten the bolt while holding the No. 4 side airbag sensor because the No. 4 side airbag sensor claw is easily damaged.



e.

Check that there is no looseness in the installation parts of the No. 4 side airbag sensor.


f.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



Hide 62632D 3.INSTALL REAR QUARTER TRIM BOARD LH (for Van)

Hide 73370E 4.INSTALL REAR SEAT OUTER BELT ASSEMBLY LH (for Van)

Hide 62520B 5.INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Wagon)

HINT:

When removing and installing the No. 2 side airbag sensor or No. 4 side airbag sensor installed on the driver side, perform this procedure.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>INSTALLATION


Hide 62510M 6.INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Wagon)

HINT:

When removing and installing the No. 2 side airbag sensor or No. 4 side airbag sensor installed on the passenger side, perform this procedure.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>INSTALLATION


Hide 67872A 7.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP LH (for Wagon)

a.

Return the No. 1 slide door weatherstrip LH to its original position.

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>INSTALLATION



Hide 67935 8.INSTALL BACK DOOR SCUFF PLATE (for Wagon)

Hide 67881A 9.INSTALL BACK DOOR WEATHERSTRIP (for Wagon)

Hide 73570A 10.INSTALL NO. 3 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (for Wagon, w/ Seat Belt)

Hide 73233 11.INSTALL OUTER LAP BELT ANCHOR COVER (for Wagon, w/ Seat Belt)

Hide 13.INSTALL REAR NO. 3 SEAT ASSEMBLY (for Wagon)

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 15. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART