Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR FLOOR AIRBAG SENSOR › from 2019.06
RM35X0E _58 Vehicle Interior _079257 SUPPLEMENTAL RESTRAINT SYSTEMS _0396603 REAR FLOOR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR FLOOR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL CLIP

NOTICE:

If the clip is removed, do not reuse it.


HINT:

Perform this procedure only when removal/installation of the clip is necessary.


a.
B550200

Attach the claw and install a new clip.


Hide 89837A 2.INSTALL REAR FLOOR SIDE AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B550199

Attach the guide and hold the rear floor side airbag sensor in place.


d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Tighten the bolt while holding the rear floor side airbag sensor because the rear floor side airbag sensor guide is easily damaged.



e.

Check that there is no looseness in the installation parts of the rear floor side airbag sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



Hide 89839A 3.INSTALL REAR FLOOR SIDE AIRBAG SENSOR COVER

NOTICE:

If the rear floor side airbag sensor cover is removed, do not reuse it.


a.

Peel off the release sheet.

NOTICE:

Do not touch the silicon coated surfaces of the tape.



b.
B550198

Install a new rear floor side airbag sensor cover.


Hide 58570C 5.INSTALL REAR FLOOR CARPET ASSEMBLY

a.

Return the rear floor carpet assembly to its original state.


Hide 6.INSTALL SEAT TRACK RAIL PROTECTOR

Hide 58595 7.INSTALL NO. 3 FLOOR CARPET MOULDING NO. 1

Hide 58595 8.INSTALL NO. 3 FLOOR CARPET MOULDING NO. 2

Hide 9.INSTALL REAR SEAT TRACK SLIDE STOPPER

Hide 62510M 10.INSTALL QUARTER TRIM PANEL ASSEMBLY RH

Hide 67871E 11.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP RH

a.

Return the No. 1 slide door weatherstrip RH to its original position.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>INSTALLATION


Hide 67881A 13.INSTALL BACK DOOR WEATHERSTRIP

Hide 73560A 14.INSTALL NO. 3 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Seat Belt)

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Wagon)>INSTALLATION


Hide 73233 15.INSTALL OUTER LAP BELT ANCHOR COVER (w/ Seat Belt)

Hide 17.INSTALL REAR NO. 3 SEAT ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 19. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 22.PERFORM SYSTEM INITIALIZATION AND CALIBRATION