Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR VALVE (w/ EGR Cooler) › 2019.06–2020.05
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384171 EGR VALVE(w/ EGR Cooler) A

1GD-FTV EMISSION CONTROL  EGR VALVE(w/ EGR Cooler)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR valve removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly


Perform initialization -
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/ Exhaust Gas Temperature Sensor for EGR

(Click here)



CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 85110 2.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55701J 3.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 26100G 4.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 87209 5.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.

w/ Rear Heater:

i.
A443316

Slide the 2 clamps and disconnect the 2 water hose sub-assemblies from the water pipe.


ii.

Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.



b.
A443317

w/o Rear Heater:

Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.


Hide 16278 6.REMOVE NO. 2 WATER BY-PASS PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A444775C01
0.104,0.146 0.354,0.323 0.25,0.177 10 true *A 0.146,2.5 0.406,2.656 0.26,0.156 10 true *B
*A w/ Heater
*B w/o Heater


for Laminated EGR Pre-cooler:

Detach the clamp, slide the clamp and disconnect the No. 18 water by-pass hose from the EGR pipe with cooler sub-assembly.


b.
A440924C01
0.083,0.083 0.323,0.24 0.24,0.156 10 true *A 0.104,2.667 0.365,2.844 0.26,0.177 10 true *B
*A w/ Heater
*B w/o Heater


w/ Viscous Heater:

Slide the clamp and disconnect the water by-pass hose sub-assembly from the No. 2 water by-pass pipe.


c.

w/ Heater:

Slide the clamp and disconnect the No. 13 water by-pass hose from the No. 2 water by-pass pipe.


d.

Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.


e.

Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR cooler.


f.
A440925C01
0.073,0.104 0.313,0.292 0.24,0.188 10 true *A 0.115,2.646 0.375,2.823 0.26,0.177 10 true *B
*A w/ Heater
*B w/o Heater


Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly.


Hide 89421C 7.REMOVE DIESEL TURBO PRESSURE SENSOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440926

Disconnect the connector from the diesel turbo pressure sensor.


b.

Disconnect the vacuum hose and remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.


Hide 23265C 8.REMOVE GAS FILTER

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440927

Disconnect the vacuum hose from the intake manifold.


b.

Detach the clamp and remove the gas filter from the gas filter bracket.


Hide 12632 9.REMOVE NO. 2 ENGINE COVER BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443361

Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly.


Hide 23941 10.DISCONNECT NO. 1 FUEL FILTER PROTECTOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440928

Disconnect the connector from the fuel filter assembly.


b.
A440929

Detach the clamp and disconnect the wire harness from the No. 1 fuel filter protector.


c.
A440930

Remove the bolt and disconnect the No. 1 fuel filter protector from the body.


Hide 82121 11.DISCONNECT ENGINE WIRE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440931

Disconnect the 2 connectors from the turbocharger sub-assembly.


b.
A440932

Detach the clamp and disconnect the connector from the intake mass air flow meter sub-assembly.


c.
A440933

Disconnect the connector from the camshaft position sensor.


d.
A440934

w/ DPF:

Disconnect the connector from the exhaust fuel addition injector assembly.


e.
A440935

Detach the 3 clamps and disconnect the engine wire from the 2 wire harness clamp brackets.


f.
A440936

w/ DPF:

i.

Detach the clamp and disconnect the connector from the differential pressure sensor.


ii.

Disconnect the 3 connectors from the exhaust gas temperature sensors.



g.
A440937

Disconnect the 4 connectors from the 4 injector assemblies.


h.
A440938

Disconnect the connector from the electric EGR control valve assembly.


i.

Disconnect the connector from the glow plug connector.


j.
A440939

Remove the bolt and disconnect the connector from the sensor wire of the common rail assembly.


k.
A440940

Disconnect the 2 connectors from the vane pump assembly.


l.
A440941

Detach the 2 clamps and disconnect the engine wire from the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.


m.
A440942

Detach the clamp, remove the bolt and disconnect the engine wire from the No. 4 water by-pass pipe sub-assembly.


Hide 25625 13.REMOVE EGR VALVE BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440943

Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.


Hide 89425D 14.REMOVE NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 25612 15.REMOVE NO. 2 EGR PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A446707C01
0.115,0.188 0.354,0.344 0.24,0.156 10 true *A 0.135,2.583 0.365,2.75 0.229,0.167 10 true *B
*A w/o Exhaust Gas Temperature Sensor for EGR
*B w/ Exhaust Gas Temperature Sensor for EGR


Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.


b.

Remove the 2 gaskets.


Hide 25800 16.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440945

Detach the clamp and disconnect the connector from the common rail assembly.


b.
A442596

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.


c.

Remove the 2 bolts and electric EGR control valve assembly.


d.

Remove the gasket.


Hide 16206B 17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A442597

Detach the clamp and disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


b.
A442598

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.


Hide 16209 18.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A442599

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 1 EGR cooler.


b.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


c.

Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.


Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443359

Remove the bolt and disconnect the No. 1 EGR pipe sub-assembly from the vacuum transmitting pipe sub-assembly.


b.
A443360

Remove the 4 nuts and No. 1 EGR pipe sub-assembly from the exhaust manifold and EGR valve adapter.


c.

Remove the 2 gaskets.


d.
A442602

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25601 20.DISCONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443342

Remove the bolt and disconnect the EGR pipe with cooler sub-assembly from the cylinder head sub-assembly.


b.
A443343

Remove the 4 nuts and disconnect the EGR pipe with cooler sub-assembly from the exhaust manifold and EGR valve adapter.


c.

Remove the 2 gaskets.


d.
A442602

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 21.REMOVE NO. 1 EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A442603C01
0.125,0.135 0.365,0.292 0.24,0.156 10 true *A 0.146,2.5 0.385,2.656 0.24,0.156 10 true *B
*A for Single Actuator EGR Bypass Valve
*B for Double Actuator EGR Bypass Valve


Remove the 4 bolts and No. 1 EGR cooler with No. 2 EGR valve assembly from the intake manifold.


Hide 25624 22.REMOVE EGR VALVE ADAPTER

a.
A442604

Remove the 2 bolts and EGR valve adapter from the No. 2 EGR valve assembly.


b.

Remove the gasket.


Hide 25630 23.REMOVE NO. 2 EGR VALVE ASSEMBLY

a.
A442605C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *A 0.115,2.542 0.427,2.698 0.313,0.156 10 false *B
*A for Single Actuator EGR Bypass Valve
*B for Double Actuator EGR Bypass Valve


Remove the 4 bolts and No. 2 EGR valve assembly from the No. 1 EGR cooler.


b.

Remove the gasket.


c.
A442606

Using an E8 "TORX" socket wrench, remove the 4 stud bolts from the No. 2 EGR valve assembly.