w/ Curtain Shield Airbag, for RH Side:
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear side window assembly RH removal/installation are shown below.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or equivalent.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR SEAT ASSEMBLY LH
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
73233
4.REMOVE OUTER LAP BELT ANCHOR COVER
67918D
5.REMOVE REAR DOOR SCUFF PLATE LH
Use the same procedure described for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67935
6.REMOVE BACK DOOR SCUFF PLATE
73370E
7.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (w/ Seat Belt)
67872A
8.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH
Use the same procedure described for the RH side.
Pull back the No. 1 slide door weatherstrip LH so that the rear quarter trim board assembly LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
62520B
9.REMOVE QUARTER TRIM PANEL ASSEMBLY LH
62639A
10.REMOVE QUARTER PILLAR GARNISH LH
62472D
11.REMOVE REAR UPPER PILLAR GARNISH LH
62460A
12.REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY LH
13.REMOVE ROOF HEADLINING ASSEMBLY (w/ Rear Air Conditioning System, for RH Side)
62170E
14.REMOVE REAR CURTAIN SHIELD AIRBAG ASSEMBLY RH (w/ Curtain Shield Airbag, for RH Side)
Use the same procedure described for the LH side.
88566B
15.REMOVE NO. 2 COOLER AIR DUCT (w/ Rear Air Conditioning System, for RH Side)
88566C
16.REMOVE NO. 3 COOLER AIR DUCT (w/ Rear Air Conditioning System, for RH Side)
Using a clip remover, detach the clip and remove the No. 3 cooler air duct.
62137G
17.REMOVE SIDE WINDOW PANEL REINFORCE (w/ Rear Air Conditioning System, for RH Side)
Remove the 2 bolts.
Detach the guide and remove the side window panel reinforce.
62740A
18.REMOVE REAR SIDE WINDOW ASSEMBLY LH
|
Protective Tape |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
When separating the rear side window assembly LH from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
| *a | Matchmark |
When reusing the rear side window assembly LH:
Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.
Install the suction cups to the rear side window assembly LH.
| *1 | Quarter Window Glass Spacer |
| *2 | Rear Side Window Clip LH |
| *a | Piano Wire |
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
Cut through the adhesive by pulling the piano wire around the rear side window assembly LH.
Using suction cups, disconnect the quarter window glass spacer and rear side window clip LH and remove the rear side window assembly LH.
Do not drop the rear side window assembly LH.