Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P023400  Turbocharger/Supercharger "A" Overboost Condition  P125100  Turbocharger Boost Control Malfunction  


DESCRIPTION

Refer to DTC P004512.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P004512

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P023400 Turbocharger/Supercharger "A" Overboost Condition When turbocharger boost pressure continues to be higher than ECM's target boost pressure. (1 trip detection logic)
·

Turbocharger nozzle vane control actuator

·

VN turbo link stuck malfunction

·

Extremely low battery voltage (P056014 stored simultaneously)

·

Intake system

·

Exhaust system

·

Electric EGR control valve assembly

·

No. 1 EGR cooler

·

Injector assembly

·

Diesel throttle body assembly

·

ECM


Comes on DTC stored SAE Code: P0234
P125100 Turbocharger Boost Control Malfunction Boost pressure is higher than the threshold* for 5 seconds (1 trip detection logic).
HINT:

*: This value changes based on engine speed, atmospheric pressure and the engine coolant temperature (the value is generally between 90 and 350 kPa).


·

Turbocharger nozzle vane control actuator

·

VN turbo link stuck malfunction

·

Extremely low battery voltage (P056014 stored simultaneously)

·

Intake system

·

Exhaust system

·

Electric EGR control valve assembly

·

No. 1 EGR cooler

·

Injector assembly

·

Diesel throttle body assembly

·

ECM


Comes on DTC stored SAE Code: P1251

Related Data List
DTC No. Data List
P023400
P125100
·

Intake Manifold Absolute Pressure

·

Target Boost Pressure

·

Mass Air Flow Sensor

·

Actual VN Turbo Position Bank 1

·

Target EGR Valve Position No.1

·

Actual EGR Valve Position No.1

·

Atmospheric Pressure



HINT:

If DTC P023400 and/or P125100 is stored due to the VN turbo vane being stuck closed, the following symptoms may appear:

·

Vehicle surge when driving with full load

·

Sudden lack of power due to power being limited



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P023400
P125100
Vehicle being driven

CAUTION / NOTICE / HINT

NOTICE:

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

HINT:
·

Record the stored DTCs and freeze frame data.

·

Be sure to carefully examine "Intake Manifold Absolute Pressure" and "Target Boost Pressure" in the freeze frame data.



Result:
Result Proceed to
DTC P023400 and/or P125100 is output A
DTC P023400 and/or P125100 and other DTCs are output B


HINT:

Variable vane DC motor-related DTCs: P004512, P004514 and P004600.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P004512

Nozzle vane position sensor-related DTCs: P256212 and P256214.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P256212




A

2.CHECK INTAKE SYSTEM

B

2.CHECK INTAKE SYSTEM
a.

Check if the hoses between the air cleaner filter element sub-assembly and turbocharger sub-assembly, and turbocharger sub-assembly and intake manifold are damaged or disconnected.

Result:
Result Proceed to
Hoses or pipes are damaged or disconnected A
No hoses or pipes are damaged or disconnected B


HINT:
·

Be sure to check if the hoses and pipes between the air cleaner and compressor are disconnected as disconnection of a hose or pipe can cause overboost. Also, check the high pressure hoses for disconnection due to overboost.

·

Check for disconnection of the exhaust pipes.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE INTAKE SYSTEM

B

4.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)
3.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the intake system.


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)
4.PERFORM ACTIVE TEST USING GTS (OPERATE TURBOCHARGER SUB-ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Turbo Charger Step Motor Bank 1 / Data List / Target VN Turbo Position Bank 1 and Actual VN Turbo Position Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Test the Turbo Charger Step Motor Bank 1
Data List Display
Target VN Turbo Position Bank 1
Actual VN Turbo Position Bank 1
50004 372 73 1125,1126

d.

While changing the Active Test value to 10, 20, 30, 40, 30, 20 and 10%, check that Actual VN Turbo Position Bank 1 smoothly changes to the set opening amount.

NOTICE:

When moving the vanes toward the fully closed position, make sure that Actual VN Turbo Position Bank 1 does not become 5% or less.


OK:

The Actual VN Turbo Position Bank 1 value follows the Target VN Turbo Position Bank 1.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)

NG

14.CHECK HARNESS AND CONNECTOR (TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR - ECM)
5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

f.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Valve Close Bank 1
Data List Display
Mass Air Flow Sensor
50004 372 71 215

h.

Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.

·

When idling the engine, the EGR cooler is bypassed.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close Bank 1:
OFF to Close
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition Mass Air Flow Sensor (Reference)
Open (41%)
·

Atmospheric pressure: 101 kPa

·

Engine coolant temperature: 75°C (167°F)


0.5 to 15 gm/sec
Closed (0%) 10 to 22 gm/sec




A

6.READ VALUE USING GTS (TARGET EGR VALVE POSITION NO.1 AND ACTUAL EGR VALVE POSITION NO.1)

B

9.READ VALUE USING GTS (TARGET INJECTION VOLUME)
6.READ VALUE USING GTS (TARGET EGR VALVE POSITION NO.1 AND ACTUAL EGR VALVE POSITION NO.1)
a.

Check the change in the values of "Target EGR Valve Position No.1" and "Actual EGR Valve Position No.1" in the Data List from the time when the "Control the EGR Step Position Bank 1" Active Test was performed in the previous step.

Result:
Result Proceed to
Even though "Target EGR Valve Position No.1" indicated that the system was commanding the valve to open, "Actual EGR Valve Position No.1" remained near 0% and did not change A
Other than above ("Actual EGR Valve Position No.1" changed according to the EGR valve open/close commands of the Active Test) B




A

7.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

8.REPLACE NO. 1 EGR COOLER
7.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve assembly, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve assembly.

·

When cleaning the electric EGR control valve assembly, perform the initialization procedure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.




c.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE NO. 1 EGR COOLER

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.READ VALUE USING GTS (TARGET INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Allow the engine to idle for 1 minute or more.

HINT:

The A/C switch and all accessory switches should be off with a fully warm engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Target Injection Volume

Powertrain > Engine > Data List
Tester Display
Target Injection Volume
50003 372 981

f.

Read the value of Target Injection Volume at 4000 rpm without load.

Result:
Result Proceed to
Target Injection Volume is less than 10.0 mm3/st A
Except above B


HINT:
·

If the injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.

·

If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector to inject.





A

10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

12.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
12.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 372 4596

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 372 4569

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off.


d.

Start the engine and warm it up.


e.

Confirm the value of Engine Speed from the Freeze Frame Data recorded previously, and then drive the vehicle according to the Engine Speed value.

HINT:

Take a snapshot of "Intake Manifold Absolute Pressure" and "Target Boost Pressure" in the Data List with the GTS while driving the vehicle.



f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P023400 and/or P125100 is not output and the amount by which Intake Manifold Absolute Pressure exceeds Target Boost Pressure is 20 kPa or less A
Except above B*


HINT:

*: Return to "Check Intake System" and inspect areas that have not been inspected yet.




A

END

B*

2.CHECK INTAKE SYSTEM
14.CHECK HARNESS AND CONNECTOR (TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR - ECM)
a.

Disconnect the variable vane DC motor connector.


b.

Disconnect the nozzle vane position sensor connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E41-1 (M-) - E7-2 (VNM-) Always Below 1 Ω
E41-2 (M+) - E7-1 (VNM+) Always Below 1 Ω
E42-3 (VTA1) - E7-23 (VNA) Always Below 1 Ω
E42-2 (VNE2) - E7-22 (VNE2) Always Below 1 Ω
E42-1 (VNVC) - E7-30 (VNVC) Always Below 1 Ω
E41-1 (M-) or E7-2 (VNM-) - Body ground and other terminals Always 10 kΩ or higher
E41-2 (M+) or E7-1 (VNM+) - Body ground and other terminals Always 10 kΩ or higher
E42-3 (VTA1) or E7-23 (VNA) - Body ground and other terminals Always 10 kΩ or higher
E42-1 (VNVC) or E7-30 (VNVC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT TURBOCHARGER NOZZLE VANE PLATE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT TURBOCHARGER NOZZLE VANE PLATE

b.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



c.
A348999

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane support plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

NG