25630
1.INSTALL NO. 2 EGR VALVE ASSEMBLY
Using an E8 "TORX" socket wrench, install the 4 stud bolts to the No. 2 EGR valve assembly.
Install a new gasket and the No. 2 EGR valve assembly to the No. 1 EGR cooler with the 4 bolts.
25624
2.INSTALL EGR VALVE ADAPTER
Install a new gasket and the EGR valve adapter to the No. 2 EGR valve assembly with the 2 bolts.
3.INSTALL NO. 1 EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY
| *A | for Single Actuator EGR Bypass Valve |
| *B | for Double Actuator EGR Bypass Valve |
for Air Cooled Type Intercooler:
Temporarily install the No. 1 EGR cooler with No. 2 EGR valve assembly to the intake manifold with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
| *1 | No. 2 Intercooler Support Bracket |
for Water Cooled Type Intercooler:
Temporarily install the No. 1 EGR cooler with No. 2 EGR valve assembly and No. 2 intercooler support bracket to the intake manifold with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
25601
4.CONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and connect the EGR pipe with cooler sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.
Connect the EGR pipe with cooler sub-assembly to the cylinder head sub-assembly with the bolt.
25601
5.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)
Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.
Install 2 new gaskets and the No. 1 EGR pipe sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.
Connect the No. 1 EGR pipe sub-assembly to the vacuum transmitting pipe sub-assembly with the bolt.
16209
6.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
for Air Cooled Type Intercooler:
| *1 | Water Hose |
| *2 | No. 7 Water By-pass Hose |
Connect the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.
Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.
Connect the No. 7 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.
for Water Cooled Type Intercooler:
| *1 | Water Hose |
| *2 | No. 7 Water By-pass Hose |
| *3 | No. 17 Water By-pass Hose |
Connect the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.
Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.
Connect the No. 7 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.
Connect the No. 17 water by-pass hose to the No. 1 EGR pipe sub-assembly, and slide the clamp to secure the hose.
16206B
7.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 3 water by-pass pipe sub-assembly to the No. 1 EGR cooler with the 2 bolts.
Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.
Attach the clamp and connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.
25800
8.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
Install a new gasket and the electric EGR control valve assembly to the No. 2 EGR valve assembly with the 2 bolts.
Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.
Attach the clamp and connect the connector to the common rail assembly.
25612
9.INSTALL NO. 2 EGR PIPE
Install 2 new gaskets and the No. 2 EGR pipe to the electric EGR control valve assembly and intake manifold with the 4 nuts.
89425D
10.INSTALL NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
25625
11.INSTALL EGR VALVE BRACKET
Install the EGR valve bracket to the electric EGR control valve assembly and intake manifold with the bolt and nut.
25804
12.INSTALL VACUUM CONTROL VALVE SET
82121
13.CONNECT ENGINE WIRE
for Air Cooled Type Intercooler:
Attach the clamp and connect the engine wire to the No. 4 water by-pass pipe sub-assembly with the bolt.
Attach the 2 clamps and connect the engine wire to the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.
Connect the 2 connectors to the vane pump assembly.
Connect the connector to the sensor wire of the common rail assembly with the bolt.
Connect the connector to the glow plug connector.
Connect the connector to the electric EGR control valve assembly.
Connect the 4 connectors to the 4 injector assemblies.
w/ DPF:
Connect the 3 connectors to the 3 exhaust gas temperature sensors.
Attach the clamp and connect the connector to the differential pressure sensor.
Attach the 3 clamps and connect the engine wire to the 2 wire harness clamp brackets.
w/ DPF:
Connect the connector to the exhaust fuel addition injector assembly.
Connect the connector to the camshaft position sensor.
Attach the clamp and connect the connector to the intake mass air flow meter assembly.
Connect the 2 connectors to the turbocharger sub-assembly.
for Water Cooled Type Intercooler:
Attach the clamp and connect the engine wire to the No. 4 water by-pass pipe sub-assembly with the bolt.
Attach the clamp and connect the engine wire to the No. 3 water by-pass pipe sub-assembly and oil level gage guide sub-assembly with the bolt.
Connect the 2 connectors to the vane pump assembly.
Connect the connector to the connecting wire.
Attach the clamp and connect the engine wire to the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly with the 2 bolts.
Connect the connector to the electric EGR control valve assembly.
Connect the connector to the glow plug connector.
Connect the connector to the connecting wire.
Connect the 4 connectors to the 4 injector assemblies.
Connect the 3 connectors to the 3 exhaust gas temperature sensors.
Connect the connector to the differential pressure sensor.
Attach the clamp and connect the engine wire to the intercooler support bracket with the 2 bolts.
Attach the 2 clamps and connect the engine wire to the wire harness clamp bracket.
Connect the connector to the exhaust fuel addition injector assembly.
Connect the connector to the camshaft position sensor.
Attach the clamp and connect the connector to the intake mass air flow meter assembly.
Attach the clamp and connect the 2 connectors to the turbocharger sub-assembly.
23941
14.CONNECT NO. 1 FUEL FILTER PROTECTOR
Connect the No. 1 fuel filter protector to the body.
Attach the clamp and connect the wire harness to the No. 1 fuel filter protector.
Connect the connector to the fuel filter assembly.
12632
15.INSTALL NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)
Install the No. 2 engine cover bracket to the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly with the 2 bolts.
23265C
16.INSTALL GAS FILTER
Attach the clamp and install the gas filter to the gas filter bracket.
Connect the vacuum hose to the intake manifold.
89421C
17.INSTALL DIESEL TURBO PRESSURE SENSOR
Connect the vacuum hose and install the diesel turbo pressure sensor to the No. 3 water by-pass pipe sub-assembly with the bolt.
Connect the connector to the diesel turbo pressure sensor.
16278
18.INSTALL NO. 2 WATER BY-PASS PIPE (for Air Cooled Type Intercooler)
Install the No. 2 water by-pass pipe to the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly with the 3 bolts.
Connect the No. 16 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.
Connect the No. 15 water by-pass hose to the water by-pass pipe, and slide the clamp to secure the hose.
w/ Heater:
Connect the No. 13 water by-pass hose to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.
w/ Viscous Heater:
Connect the water by-pass hose sub-assembly to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.
for Laminated EGR Pre-cooler:
Attach the clamp, connect the No. 18 water by-pass hose to the EGR pipe with cooler sub-assembly, and slide the clamp to secure the hose.
87209
19.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)
for Air Cooled Type Intercooler:
w/ Rear Heater:
Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.
Connect the 2 water hose sub-assemblies to the water pipe, and slide the 2 clamps to secure the hoses.
w/o Rear Heater:
Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.
for Water Cooled Type Intercooler:
Install the 2 water hose sub-assemblies to the air conditioning unit assembly and water pipe, and slide the 4 clamps to secure the hoses.
26100G
20.INSTALL DIESEL THROTTLE BODY ASSEMBLY
17940D
21.INSTALL INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)
55701J
22.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
85110
23.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
24.ADD ENGINE COOLANT (for Air Cooled Type Intercooler)
25.INSPECT FOR COOLANT LEAK (for Air Cooled Type Intercooler)