When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Make sure foreign matter does not enter the fuel path.
22100
1.INSTALL SUPPLY PUMP ASSEMBLY
| *A | w/ Pressurized Fuel Filter |
| *B | w/o Pressurized Fuel Filter |
Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.
With SST set, do not turn the crankshaft more than a half rotation.
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the supply pump assembly.
| *a | Groove |
To insert the supply pump assembly shaft in the supply pump shaft sprocket, it may be necessary to turn the supply pump assembly several degrees and the groove in the supply pump assembly shaft are aligned.
| *a | Supply Pump Shaft Key |
| *b | Upper Side |
When installing a new supply pump assembly, adjust the supply pump assembly injection pump drive shaft key assignment by turning the supply pump assembly shown in the illustration.
| *a | Hold |
|
Turn |
Using SST, tighten clockwise direction the supply pump assembly, and then temporarily install the 3 fuel supply pump fixing nuts.
Using SST, tighten and insert the supply pump assembly up to the position shown in the illustration and tighten the 3 fuel supply pump fixing nuts.
After tightening the part with SST, a gap of 2 to 3 mm in area A shown in the illustration is normal.
Install the No. 1 fuel pump bracket with the 2 bolts to the supply pump assembly and cylinder block sub-assembly.
Remove SST and the 3 set bolts.
| *a | Hold |
|
Turn |
Using SST, hold the crankshaft pulley sub-assembly and tighten the supply pump shaft nut.
11324
2.INSTALL TIMING CHAIN COVER PLATE
Install the timing chain cover plate and new gasket with the 3 bolts.
Do not install the timing chain cover plate with the bolts included with SST.
23243B
3.INSTALL FUEL PUMP MOTOR WIRE
Attach the clamp and install the fuel pump motor wire.
Connect the fuel pump motor wire connector.
22803
4.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY
Install the fuel injection pump cover sub-assembly to the supply pump assembly.
5.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter without DPF)
Tighten the No. 4 fuel pipe with the 2 union bolts and bolts with 2 new gaskets in the order shown in the illustration.
23271H
6.INSTALL NO. 1 FUEL HOSE
Install the No. 1 fuel hose to the supply pump assembly and No. 2 fuel pipe, and slide the 2 clips to secure the hoses.
23273H
7.INSTALL NO. 2 FUEL HOSE
Install the No. 2 fuel hose to the supply pump assembly and No. 3 nozzle leakage pipe assembly, and slide the 2 clips to secure the hoses.
16620
8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
16711
9.INSTALL FAN SHROUD
10.CONNECT INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)
88359
11.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)
161B0
12.INSTALL ELECTRIC WATER PUMP ASSEMBLY (for Water Cooled Type Intercooler)
16551C
13.INSTALL NO. 1 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)
16552C
14.INSTALL NO. 2 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)
16571C
15.INSTALL NO. 1 RADIATOR HOSE
16470
16.INSTALL RADIATOR RESERVE TANK ASSEMBLY
16640
17.INSTALL INTERCOOLER RESERVE TANK ASSEMBLY (for Water Cooled Type Intercooler)
44360
18.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
17303T
19.INSTALL AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)
25761B
20.CONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type Intercooler)
17030
21.INSTALL AIR HOSE ASSEMBLY (for Air Cooled Type Intercooler)
17751
22.INSTALL NO. 1 AIR CLEANER INLET
53106B
23.INSTALL RADIATOR COVER SUB-ASSEMBLY
51405A
24.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
52618
25.INSTALL LOWER FRONT BUMPER ABSORBER
51406A
26.INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
17111
27.INSTALL INTAKE MANIFOLD
28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
29. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
30.BLEED AIR FROM FUEL SYSTEM
31.INSPECT FOR FUEL LEAK