Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR COOLER › from 2021.07
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384172 EGR COOLER A

1GD-FTV EMISSION CONTROL  EGR COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR cooler removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly


Perform initialization -
·

w/ DPF:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

for Water Cooled Type Intercooler

(Click here)



CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT (for Air Cooled Type Intercooler)

Hide 85110 2.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55701J 3.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 17940D 4.REMOVE INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 26100G 5.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 87209 6.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)

Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE (for Air Cooled Type Intercooler)

Hide 89421C 8.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 12632 10.REMOVE NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)

Hide 23941 11.DISCONNECT NO. 1 FUEL FILTER PROTECTOR

Hide 16206B 16.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.

for Air Cooled Type Intercooler:

i.
A442597

Detach the clamp and disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


ii.
A442616

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.


iv.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.



b.

for Water Cooled Type Intercooler:

i.
A452843

Detach the clamp and disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


ii.
A452852

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.


iv.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.



Hide 16209 17.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

Hide 25601 19.DISCONNECT EGR PIPE SUB-ASSEMBLY NO.1 (for Double Actuator EGR Bypass Valve)

Hide 20.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A442617C01
0.135,0.156 0.406,0.313 0.271,0.156 10 true *A 0.146,2.51 0.375,2.677 0.229,0.167 10 true *B
*A for Single Actuator EGR Bypass Valve
*B for Double Actuator EGR Bypass Valve


for Air Cooled Type Intercooler:

Remove the 4 bolts and No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly from the intake manifold.


b.
A452853

for Water Cooled Type Intercooler:

Remove the 4 bolts and No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly and No. 2 intercooler support bracketfrom the intake manifold.


Hide 25681 21.REMOVE NO. 1 EGR COOLER

a.
A442618C01
0.104,0.177 0.417,0.333 0.313,0.156 10 false *A 0.146,2.469 0.458,2.625 0.313,0.156 10 false *B
*A for Single Actuator EGR Bypass Valve
*B for Double Actuator EGR Bypass Valve


Remove the 4 bolts and No. 1 EGR cooler from the No. 2 EGR valve assembly with electric EGR control valve assembly.


b.

Remove the gasket.