Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.
11.
INSTALL FRONT PILLAR GARNISH RH
Remove the protective cover.
Install a new clip <A> on the front pillar garnish RH.
Engage the 3 guides and 2 clips, then install the front pillar garnish RH.
12.
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
NOTICE:
After installation, check that the corners fit correctly.
13.
INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Install a new clip <A> on the front pillar garnish LH.
Engage the 3 guides and 2 clips, then install the front pillar garnish LH.
14.
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
NOTICE:
After installation, check that the corners fit correctly.
15.
INSTALL ENGINE SWITCH (w/ Smart Entry and Start System)
Engage the 2 claws to install the switch.
Connect the switch connector.
16.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for LHD)
Engage the claw and 2 guides.
Install the front No. 2 console box insert with the 3 screws <F> and clip.
17.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)
Engage the claw and 2 guides.
Install the front No. 2 console box insert with the 3 screws <F> and clip.
18.
INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)
Engage the claw and 2 guides.
Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.
19.
INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)
Engage the claw and 2 guides.
Install the front No. 1 console box insert with the 3 screws <F> and clip.
20.
INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)
Engage the 6 claws.
Install the console box assembly with the 4 bolts and 2 screws.
21.
INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)
Engage the 6 claws.
Connect the connector.
Install the console box assembly with the 4 bolts and 2 screws.
Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.
43.
POSITION FRONT WHEELS STRAIGHT AHEAD
44.
INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
45.
INSTALL STEERING COLUMN COVER
Engage the claw to install the upper steering column cover.
Engage the 2 claws to install the lower steering column cover.
Install the 2 screws.
Torque:
2.0 N*m{
20 kgf*cm
, 18 in.*lbf
}
46.
ADJUST SPIRAL CABLE
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.
Rotate the spiral cable counterclockwise slowly by hand until it stops.
NOTICE:
Do not turn the spiral cable using the airbag wire harness.
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
NOTICE:
Do not turn the spiral cable using the airbag wire harness.
HINT:
The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
47.
INSTALL STEERING WHEEL ASSEMBLY
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Torque:
50 N*m{
510 kgf*cm
, 37 ft.*lbf
}
Connect the connectors to the spiral cable sub-assembly.
48.
INSPECT STEERING WHEEL CENTER POINT
49.
INSTALL STEERING PAD
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.
Support the steering pad with one hand as shown in the illustration.
Connect the 2 airbag connectors to the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
Torque:
8.8 N*m{
90 kgf*cm
, 78 in.*lbf
}
50.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
Install the lower No. 2 steering wheel cover with the claw.
51.
INSTALL LOWER NO. 3 STEERING WHEEL COVER
Install the lower No. 3 steering wheel cover with the claw.
52.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
53.
INSPECT STEERING PAD
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.
Make sure that the horn sounds.
HINT:
If the horn does not sound, inspect the horn system (Click here).