2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Door Courtesy Switch Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The main body ECU receives courtesy switch signals to control the illuminated entry system and light auto turn off system.

WIRING DIAGRAM

E151675E02
E151675E05

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Body Electrical / Main Body / Data List.

  1. Read the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D door Courtesy SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door open
    OFF: Driver side door closed
    -
    P door Courtesy SW
    Front passenger side door courtesy switch signal / ON or OFF
    ON: Front passenger side door open
    OFF: Front passenger side door closed
    -
    RR door Courtesy SW
    Rear door courtesy switch RH signal / ON or OFF
    ON: Rear door RH open
    OFF: Rear door RH closed
    -
    RL door Courtesy SW
    Rear door courtesy switch LH signal / ON or OFF
    ON: Rear door LH open
    OFF: Rear door LH closed
    -
    Back door Courtesy SW
    Back door Courtesy switch signal / ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    Glass Hatch Courtesy Switch
    Back window Courtesy Switch signal / ON or OFF
    ON: Back window open
    OFF: Back window closed
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT COURTESY SWITCH
  1. Inspect the front door courtesy switches (Click here).

  1. Inspect the rear door courtesy switches (Click here).

  1. Inspect the back door courtesy switch (Click here).

  1. Inspect the back window courtesy switch (Click here).

    OK:
    Courtesy switches are normal.



NG
REPLACE COURTESY SWITCH
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COURTESY SWITCH)

  1. E121487E10
    Check the harness and connector between the main body ECU and front door courtesy switch LH (for LHD).
    1. Disconnect the D7 main body ECU connector.

    2. Disconnect the O2 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D7-24 (DCTY) - O2-1
      Always
      Below 1 Ω
      D7-24 (DCTY) - Body ground
      Always
      10 kΩ or higher

  1. E108574E23
    Check the harness and connector between the main body ECU and front door courtesy switch LH (for RHD).
    1. Disconnect the D6 main body ECU connector.

    2. Disconnect the O2 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D6-21 (PCTY) - O2-1
      Always
      Below 1 Ω
      D6-21 (PCTY) - Body ground
      Always
      10 kΩ or higher

  1. E108574E21
    Check the harness and connector between the main body ECU and front door courtesy switch RH (for LHD).
    1. Disconnect the D6 main body ECU connector.

    2. Disconnect the N2 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D6-21 (PCTY) - N2-1
      Always
      Below 1 Ω
      D6-21 (PCTY) - Body ground
      Always
      10 kΩ or higher

  1. E121487E11
    Check the harness and connector between the main body ECU and front door courtesy switch RH (for RHD).
    1. Disconnect the D7 main body ECU connector.

    2. Disconnect the N2 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D7-24 (DCTY) - N2-1
      Always
      Below 1 Ω
      D7-24 (DCTY) - Body ground
      Always
      10 kΩ or higher

  1. E121486E07
    Check the harness and connector between the instrument panel junction block and rear door courtesy switch LH.
    1. Disconnect the 1O instrument panel junction block connector.

    2. Disconnect the O8 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1O-7 (LCTY) - O8-1
      Always
      Below 1 Ω
      1O-7 (LCTY) - Body ground
      Always
      10 kΩ or higher

  1. E108574E22
    Check the harness and connector between the main body ECU and rear door courtesy switch RH.
    1. Disconnect the D6 main body ECU connector.

    2. Disconnect the N7 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D6-7 (RCTY) - N7-1
      Always
      Below 1 Ω
      D6-7 (RCTY) - Body ground
      Always
      10 kΩ or higher

  1. E151694E02
    Check the harness and connector between the main body ECU and back door lock assembly.
    1. Disconnect the D6 main body ECU connector.

    2. Disconnect the T4*1 or T3*2 back door lock assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D6-25 (BCTY) - T4-3*1
      Always
      Below 1 Ω
      D6-25 (BCTY) - T3-3*2
      Always
      Below 1 Ω
      D6-25 (BCTY) - Body ground
      Always
      10 kΩ or higher

      *1: w/ Power Back Door*2: w/o Power Back Door

  1. E151693E03
    Check the harness and connector between the main body ECU and back window lock assembly (w/ Glass Hatch Opener).
    1. Disconnect the D7 main body ECU connector.

    2. Disconnect the T6 back window lock assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D7-20 (GCTY) - T6-2
      Always
      Below 1 Ω
      D7-20 (GCTY) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Light Control Switch Circuit (from Jul 2010)Door Courtesy Switch Circuit (Aug 2008 – Jun 2010) →