Door Courtesy Switch Circuit
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The main body ECU receives courtesy switch signals to control the illuminated entry system and light auto turn off system.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Select the following menu items: Body Electrical / Main Body / Data List.
Read the display on the intelligent tester.
Main Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D door Courtesy SW
Driver side door courtesy switch signal / ON or OFF
ON: Driver side door open
OFF: Driver side door closed
-
P door Courtesy SW
Front passenger side door courtesy switch signal / ON or OFF
ON: Front passenger side door open
OFF: Front passenger side door closed
-
RR door Courtesy SW
Rear door courtesy switch RH signal / ON or OFF
ON: Rear door RH open
OFF: Rear door RH closed
-
RL door Courtesy SW
Rear door courtesy switch LH signal / ON or OFF
ON: Rear door LH open
OFF: Rear door LH closed
-
Back door Courtesy SW
Back door Courtesy switch signal / ON or OFF
ON: Back door open
OFF: Back door closed
-
Glass Hatch Courtesy Switch
Back window Courtesy Switch signal / ON or OFF
ON: Back window open
OFF: Back window closed
-
- OK:
- Normal conditions listed above are displayed.
|
|
||||
| OK | ||
| ||
| 2. INSPECT COURTESY SWITCH |
Inspect the front door courtesy switches (Click here).
Inspect the rear door courtesy switches (Click here).
Inspect the back door courtesy switch (Click here).
Inspect the back window courtesy switch (Click here).
- OK:
- Courtesy switches are normal.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - COURTESY SWITCH) |
Check the harness and connector between the main body ECU and front door courtesy switch LH (for LHD).

Disconnect the D7 main body ECU connector.
Disconnect the O2 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D7-24 (DCTY) - O2-1
Always
Below 1 Ω
D7-24 (DCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the main body ECU and front door courtesy switch LH (for RHD).

Disconnect the D6 main body ECU connector.
Disconnect the O2 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D6-21 (PCTY) - O2-1
Always
Below 1 Ω
D6-21 (PCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the main body ECU and front door courtesy switch RH (for LHD).

Disconnect the D6 main body ECU connector.
Disconnect the N2 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D6-21 (PCTY) - N2-1
Always
Below 1 Ω
D6-21 (PCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the main body ECU and front door courtesy switch RH (for RHD).

Disconnect the D7 main body ECU connector.
Disconnect the N2 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D7-24 (DCTY) - N2-1
Always
Below 1 Ω
D7-24 (DCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the instrument panel junction block and rear door courtesy switch LH.

Disconnect the 1O instrument panel junction block connector.
Disconnect the O8 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1O-7 (LCTY) - O8-1
Always
Below 1 Ω
1O-7 (LCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the main body ECU and rear door courtesy switch RH.

Disconnect the D6 main body ECU connector.
Disconnect the N7 switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D6-7 (RCTY) - N7-1
Always
Below 1 Ω
D6-7 (RCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the main body ECU and back door lock assembly.

Disconnect the D6 main body ECU connector.
Disconnect the T4*1 or T3*2 back door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D6-25 (BCTY) - T4-3*1
Always
Below 1 Ω
D6-25 (BCTY) - T3-3*2
Always
Below 1 Ω
D6-25 (BCTY) - Body ground
Always
10 kΩ or higher
Check the harness and connector between the main body ECU and back window lock assembly (w/ Glass Hatch Opener).

Disconnect the D7 main body ECU connector.
Disconnect the T6 back window lock assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D7-20 (GCTY) - T6-2
Always
Below 1 Ω
D7-20 (GCTY) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
