2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the vehicle has a built-in type amplifier, the sound signals are sent from the navigation receiver assembly to the speakers via this circuit.

WIRING DIAGRAM

E153703E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR
  1. Disconnect the E6 navigation receiver assembly connector.

  1. Disconnect the E7 navigation receiver assembly connector.

  1. Disconnect the H5 and G5 front No. 1 speaker connectors.

  1. Disconnect the F2 and f2 front No. 2 speaker connectors.

  1. Disconnect the K1 and J1 rear speaker connectors.

  1. Measure the resistance between each of the front No. 2 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - F2-2
    Always
    Below 1 Ω
    E6-6 (FL-) - F2-4
    Always
    Below 1 Ω
    E6-1 (FR+) - f2-2
    Always
    Below 1 Ω
    E6-5 (FR-) - f2-4
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - H5-1
    Always
    Below 1 Ω
    E6-6 (FL-) - H5-2
    Always
    Below 1 Ω
    E6-1 (FR+) - G5-1
    Always
    Below 1 Ω
    E6-5 (FR-) - G5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speakers and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-2 (RL+) - K1-1
    Always
    Below 1 Ω
    E7-6 (RL-) - K1-2
    Always
    Below 1 Ω
    E7-1 (RR+) - J1-1
    Always
    Below 1 Ω
    E7-3 (RR-) - J1-2
    Always
    Below 1 Ω

  1. Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E6-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    E6-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E6-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    E7-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E7-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    E7-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E7-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT NO. 1 SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H5-1 - H5-2
      Always
      3.2 to 4.8 Ω
      G5-1 - G5-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.



NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


3. INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 4
OK

REPLACE FRONT NO. 2 SPEAKER (Click here)

4. INSPECT REAR SPEAKER
  1. Resistance check

    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K1-1 - K1-2
      Always
      3.2 to 4.8 Ω
      J1-1 - J1-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.



NG
REPLACE REAR SPEAKER (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Speaker Circuit (Aug 2008 – Jun 2010)Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter (from Jul 2010) →