2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jul 2010

DESCRIPTION

The sound signals amplified by the navigation receiver assembly are sent to the speakers from the navigation receiver assembly via the speaker circuit.
If there is a short in a speaker circuit, the navigation receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

E210066E01
E210067E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR
  1. Disconnect the E6 navigation receiver assembly connector.

  1. Disconnect the E7 navigation receiver assembly connector.

  1. Disconnect the H5 and G5 front No. 1 speaker assembly connectors.

  1. Disconnect the F2 and f2 front No. 2 speaker assembly connectors.

  1. Disconnect the K1 and J1 rear speaker assembly connectors.

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - H5-1
    Always
    Below 1 Ω
    E6-6 (FL-) - H5-2
    Always
    Below 1 Ω
    E6-1 (FR+) - G5-1
    Always
    Below 1 Ω
    E6-5 (FR-) - G5-2
    Always
    Below 1 Ω
    E6-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E6-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E6-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    E6-6 (FL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - F2-2
    Always
    Below 1 Ω
    E6-6 (FL-) - F2-4
    Always
    Below 1 Ω
    E6-1 (FR+) - f2-2
    Always
    Below 1 Ω
    E6-5 (FR-) - f2-4
    Always
    Below 1 Ω
    E6-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E6-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    E6-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E6-5 (FR-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the rear speaker assemblies and the navigation receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-2 (RL+) - K1-1
    Always
    Below 1 Ω
    E7-6 (RL-) - K1-2
    Always
    Below 1 Ω
    E7-1 (RR+) - J1-1
    Always
    Below 1 Ω
    E7-3 (RR-) - J1-2
    Always
    Below 1 Ω
    E7-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E7-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    E7-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E7-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT NO. 1 SPEAKER

  1. E210109E03
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H5-1 - H5-2
      Always
      3.2 to 4.8 Ω
      G5-1 - G5-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

Text in Illustration 
*a
Component without harness connected
(Front No. 1 Speaker Assembly)


NG
REPLACE FRONT NO. 1 SPEAKER (Click here)
OK


3. INSPECT FRONT NO. 2 SPEAKER
  1. Check that the malfunction disappears when another speaker in good condition is installed.

    Standard:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 4
OK

REPLACE FRONT NO. 2 SPEAKER (Click here)

4. INSPECT REAR SPEAKER

  1. E210109E04
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K1-1 - K1-2
      Always
      3.2 to 4.8 Ω
      J1-1 - J1-2
      Always
      3.2 to 4.8 Ω

      NOTICE:
      The speaker should not be removed to check resistance.

Text in Illustration 
*a
Component without harness connected
(Rear Speaker Assembly)


NG
REPLACE REAR SPEAKER (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Parking Brake Switch Circuit (from Jul 2010)Sound Signal Circuit between Navigation Receiver Assembly and Multi-media Interface ECU (from Jul 2010) →