2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

If there is a short in this circuit, the radio receiver detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver or speakers.

WIRING DIAGRAM

E216475E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio receiver and the speakers.

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - F2-2
    Always
    Below 1 Ω
    E6-6 (FL-) - F2-4
    Always
    Below 1 Ω
    E6-1 (FR+) - f2-2
    Always
    Below 1 Ω
    E6-5 (FR-) - f2-4
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - H5-1
    Always
    Below 1 Ω
    E6-6 (FL-) - H5-2
    Always
    Below 1 Ω
    E6-1 (FR+) - G5-1
    Always
    Below 1 Ω
    E6-5 (FR-) - G5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the radio receiver to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-2 (RL+) - K1-1
    Always
    Below 1 Ω
    E7-6 (RL-) - K1-2
    Always
    Below 1 Ω
    E7-1 (RR+) - J1-1
    Always
    Below 1 Ω
    E7-3 (RR-) - J1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each speaker and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E6-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    E6-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E6-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    E7-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E7-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    E7-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E7-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E210109E03
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H5-1 - H5-2
      Always
      3.2 to 4.8 Ω
      G5-1 - G5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when another speaker in good condition is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 4
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

4. INSPECT REAR SPEAKER ASSEMBLY

  1. E210109E05
    Resistance check
    1. Measure the resistance between the terminals of the speaker.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K1-1 - K1-2
      Always
      3.2 to 4.8 Ω
      J1-1 - J1-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Speaker Circuit (Aug 2008 – Jun 2010)Sound Signal Circuit between Radio Receiver and Multi-media Interface ECU (from Jul 2010) →