2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line for Short to +B (LHD Models)

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

There may be a short circuit between one of the CAN bus wires and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B in CAN bus wire
  2. Skid control ECU
  3. Power steering ECU
  4. Steering angle sensor
  5. Yaw rate sensor
  6. ECM
  7. Center airbag sensor assembly
  8. Air conditioning amplifier
  9. Combination meter ECU
  10. Main body ECU
  11. CAN junction connector CTR
  12. CAN junction connector RH

WIRING DIAGRAM

C227428E03
C228506E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If the doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)
  1. Turn the ignition switch off, and disconnect negative battery terminal.

  1. Disconnect the CAN junction connector CTR.

  1. Measure the resistance according to the value(s) in the table below.C170177E12

    Standard Resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D47-1 (CANH) - D43-16 (BAT)
    SB - LG
    CAN junction connector RH
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-12 (CANL) - D43-16 (BAT)
    W - LG
    CAN junction connector RH
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-4 (CANH) - D43-16 (BAT)
    L - LG
    DLC3
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-15 (CANL) - D43-16 (BAT)
    W - LG
    DLC3
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-6 (CANH) - D43-16 (BAT)
    P - LG
    Combination meter
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-17 (CANL) - D43-16 (BAT)
    W - LG
    Combination meter
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (DLC3 branch wire)
    B
    NG (Combination meter main wire)
    C
    NG (CAN junction connector RH main wire)
    D



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3

C
Go to step 4

D
Go to step 5
A


2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)

  1. Measure the resistance according to the value(s) in the table below.C170177E13

    Standard Resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D47-2 (CANH) - D43-16 (BAT)
    V - LG
    Yaw rate sensor
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-13 (CANL) - D43-16 (BAT)
    W - LG
    Yaw rate sensor
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-3 (CANH) - D43-16 (BAT)
    Y - LG
    Center airbag sensor assembly
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-14 (CANL) - D43-16 (BAT)
    W - LG
    Center airbag sensor assembly
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-5 (CANH) - D43-16 (BAT)
    R - LG
    Steering angle sensor
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-16 (CANL) - D43-16 (BAT)
    W - LG
    Steering angle sensor
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Yaw rate sensor branch wire)
    B
    NG (Center airbag sensor assembly branch wire)
    C
    NG (Steering angle sensor branch wire)
    D



B
Go to step 8

C
Go to step 9

D
Go to step 10
A


3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)

  1. Measure the resistance according to the value(s) in the table below.C227430E01

    Standard Resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D47-7 (CANH) - D43-16 (BAT)
    B - LG
    Power steering ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-18 (CANL) - D43-16 (BAT)
    W - LG
    Power steering ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-8 (CANH) - D43-16 (BAT)
    GR - LG
    Main body ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-19 (CANL) - D43-16 (BAT)
    W - LG
    Main body ECU
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Power steering ECU branch wire)
    B
    NG (Main body ECU branch wire)
    C



B
Go to step 11

C
Go to step 12
A

REPLACE CAN JUNCTION CONNECTOR CTR

4. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER MAIN WIRE)

  1. C229505E01
    Disconnect the combination meter connector.

  1. C170244E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-6 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-17 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER MAIN WIRE)
OK

REPLACE COMBINATION METER (Click here)

5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)
  1. Disconnect the CAN junction connector RH.

  1. Measure the resistance according to the value(s) in the table below.C170177E15

    HINT:
    The resistance must be measured after the CAN junction connector CTR is disconnected.


    Standard Resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D51-1 (CANH) - D43-16 (BAT)
    R - LG
    ECM
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-12 (CANL) - D43-16 (BAT)
    W - LG
    ECM
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-5 (CANH) - D43-16 (BAT)
    SB - LG
    CAN junction connector CTR
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-16 (CANL) - D43-16 (BAT)
    W - LG
    CAN junction connector CTR
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (ECM main wire)
    B
    NG (CAN junction connector CTR main wire)
    C



B
Go to step 7

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR CTR - CAN JUNCTION CONNECTOR RH)
A


6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)

  1. Measure the resistance according to the value(s) in the table below.C228954E01

    Standard Resistance:
    Tester Connection
    Wiring Color
    Connected to
    Condition
    Specified Condition
    D51-3 (CANH) - D43-16 (BAT)
    LG - LG
    Air conditioning amplifier
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-14 (CANL) - D43-16 (BAT)
    W - LG
    Air conditioning amplifier
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-4 (CANH) - D43-16 (BAT)
    B - LG
    Skid control ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-15 (CANL) - D43-16 (BAT)
    W - LG
    Skid control ECU
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Air conditioning amplifier branch wire)
    B
    NG (Skid control ECU branch wire)
    C



B
Go to step 13

C
Go to step 14
A

REPLACE CAN JUNCTION CONNECTOR RH

7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)

  1. C228959E01
    Disconnect the ECM connector.

  1. C170244E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-1 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-12 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM MAIN WIRE)
OK

REPLACE ECM (Click here)

8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)

  1. C165630E04
    Disconnect the yaw rate sensor connector.

  1. C170244E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-2 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-13 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR BRANCH WIRE)
OK

REPLACE YAW RATE SENSOR (Click here)

9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

  1. C131069E22
    Disconnect the center airbag sensor assembly connector.

  1. C170244E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-3 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-14 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. C165753E03
    Disconnect the steering angle sensor connector.

  1. C170244E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-5 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-16 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR BRANCH WIRE)
OK

REPLACE STEERING ANGLE SENSOR (Click here)

11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)

  1. C128052E11
    Disconnect the power steering ECU connector.

  1. C170244E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-7 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-18 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU BRANCH WIRE)
OK

REPLACE POWER STEERING ECU (Click here)

12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU BRANCH WIRE)

  1. C195604E05
    Disconnect the main body ECU connector.

  1. C170244E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-8 (CANH) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D47-19 (CANL) - D43-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU BRANCH WIRE)
OK

REPLACE MAIN BODY ECU

13. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. C152868E06
    Disconnect the air conditioning amplifier connector.

  1. C170244E11
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-3 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-14 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)

14. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. C156384E48
    Disconnect the skid control ECU connector.

  1. C170244E12
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D51-4 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D51-15 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← Check CAN Bus Line for Short to +B (LHD Models) (Aug 2008 – Jun 2010)Check CAN Bus Line for Short to GND (LHD Models) (May 2007 – Jul 2008) →