2007-2013 Highlander Kluger · Service Manual BRAKE

Downhill Assist Control Indicator Light Remains ON

Circuit diagnosis · Vehicles built Jul 2010 – Jun 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
The downhill assist control indicator light comes on when the downhill assist control is ready.
Even if the downhill assist control switch is pressed, the downhill assist control indicator light will blink and the downhill assist control will not be activated under the following conditions:
  1. ABS is malfunctioning.
  2. Temperature of the brake actuator increases and the downhill assist control is temporarily canceled.

HINT:
For vehicles with the multi-information display, the master caution indicator light will come on and a warning message will be displayed on the multi-information display if the downhill assist control cannot be performed.
If any of the following conditions is met with the downhill assist control switch on, a message will be displayed on the multi-information display to inform that the downhill assist control cannot be performed:
  1. The shift lever is in any position other that S1 or R.
  2. The vehicle speed is 25 km/h (16 mph) or more.


WIRING DIAGRAM

C170468E06

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (for 2GR-FE) (Click here)
OK


4. READ VALUE ON INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Downhill Assist Control SW
    Downhill assist control switch / ON or OFF
    ON: Switch ON
    OFF: Switch OFF
    -

  1. Using the intelligent tester, check the switch condition on the intelligent tester changes according to downhill assist control switch operation.

    OK:
    The intelligent tester display changes according to downhill assist control switch operation.



NG
Go to step 6
OK


5. INSPECT COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Perform the Active Test of the combination meter (meter CPU) using the intelligent tester (Click here).

  1. Check the combination meter.

    OK:
    The downhill assist control indicator light turns on or off in accordance with the intelligent tester operation.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

6. INSPECT DOWNHILL ASSIST CONTROL SWITCH

  1. C156507E01
    Turn the ignition switch off.

  1. Disconnect the downhill assist control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (B) - 1 (E)
    Switch is pushed in
    Below 1 Ω
    4 (B) - 1 (E)
    Switch is not pushed in
    10 kΩ or higher

    NOTICE:
    Check the downhill assist control switch signal after replacement (Click here).



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DOWNHILL ASSIST CONTROL SWITCH)

  1. C168258E01
    Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-26 (HDCS) - g2-4 (B)
    Always
    Below 1 Ω
    A24-26 (HDCS) - Body ground
    Always
    10 kΩ or higher
    g2-1 (E) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← Downhill Assist Control Indicator Light Remains ON (Aug 2008 – Jun 2010)Downhill Assist Control Indicator Light Remains ON (from Jul 2012) →