B2342 Switch Failure
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
This DTC is output when the sliding roof drive gear sub-assembly (sliding roof control ECU) detects that the OPEN, CLOSE, UP or DOWN switch in the roof console box assembly (sliding roof switch assembly) is stuck for 30 seconds or more.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2342 |
Sliding roof drive gear sub-assembly (sliding roof control ECU) detects OPEN, CLOSE, UP or DOWN switch in roof console box assembly (sliding roof switch assembly) is stuck for 30 seconds or more |
|
WIRING DIAGRAM
Refer to DTC B2341 (Click here).INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (SLIDE OPEN AND TILT UP SWITCH) |
Use the DATA LIST to check if the sliding roof switch assembly is functioning properly.
Sliding roof ECU Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
OPEN SW
(Open Switch)
Slide switch open signal/ON or OFF
ON: OPEN switch is pressed.
OFF: OPEN switch is not pressed.
-
CLOSE SW
(Close Switch)
Slide switch close signal/ON or OFF
ON: CLOSE switch is pressed.
OFF: CLOSE switch is not pressed.
-
UP SW
(Up Switch)
Tilt switch up signal/ON or OFF
ON: UP switch is pressed.
OFF: UP switch is not pressed.
-
DOWN SW
(Down Switch)
Tilt switch down signal/ON or OFF
ON: DOWN switch is pressed.
OFF: DOWN switch is not pressed.
-
- OK:
- The intelligent tester displays as shown in the table according to the operation of each switch.
|
|
||||
| OK | |
| 2. CHECK SLIDING ROOF FUNCTION |
Check the auto operation with the OPEN, CLOSE, UP and DOWN switches (Click here).
- OK:
- Auto operation operates normally with OPEN, CLOSE, UP and DOWN switches.
|
|
||||
| OK | |
| 3. RECHECK FOR DTC |
Delete the DTCs (Click here).
Recheck for DTCs (Click here).
- HINT:
- If DTCs are detected frequently, replace the ECU.
- OK:
- DTC is not output.
|
|
||||
| OK | ||
| ||
| 4. INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) |
Remove the roof console box assembly.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
Q1-3 (CLS) - Q1-2 (GND)
CLOSE
Below 100 Ω
Q1-4 (OPN) - Q6-2 (GND)
OPEN
Below 100 Ω
Q1-5 (DOWN) - Q1-2 (GND)
DOWN
Below 100 Ω
Q1-6 (UP) - Q1-2 (GND)
UP
Below 100 Ω
Q1-3 (CLS) - Q1-2 (GND)
OPEN
1 kΩ or higher
Q1-4 (OPN) - Q1-2 (GND)
CLOSE
1 kΩ or higher
Q1-5 (DOWN) - Q1-2 (GND)
UP
1 kΩ or higher
Q1-6 (UP) - Q1-2 (GND)
DOWN
1 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY) |
Disconnect the Q12 and Q1 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Q12-2 (E) - Q1-2 (GND)
Always
Below 1 Ω
Q12-7 (OPN) - Q1-4 (OPN)
Always
Below 1 Ω
Q12-8 (DWN) - Q1-5 (DOWN)
Always
Below 1 Ω
Q12-9 (CLS) - Q1-3 (CLS)
Always
Below 1 Ω
Q12-10 (UP) - Q1-6 (UP)
Always
Below 1 Ω
Q1-3 (CLS) - Body ground
Always
10 kΩ or higher
Q1-4 (OPN) - Body ground
Always
10 kΩ or higher
Q1-2 (GND) - Body ground
Always
Below 1 Ω
Q1-5 (DOWN) - Body ground
Always
10 kΩ or higher
Q1-6 (UP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) |
Temporarily replace the roof console box assembly (sliding roof switch assembly) with a new one or normally functioning one (Click here).
Perform the initialization (Click here)
| NEXT | |
| 7. RECHECK FOR DTC |
Delete the DTCs (Click here).
Recheck for DTCs (Click here).
- HINT:
- If DTCs are detected frequently, replace the ECU.
- OK:
- DTC is not output.
|
|
||||
| OK | ||
| ||
| 8. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU) |
Check that the sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized (Click here).
- OK:
- Sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized.
|
|
||||
| OK | |
| 9. CHECK SLIDING ROOF FUNCTION |
Check the auto operation with the OPEN, CLOSE, UP and DOWN switches (Click here).
- OK:
- Auto operation operates normally with OPEN, CLOSE, UP and DOWN switches.
|
|
||||
| OK | |
| 10. RECHECK FOR DTC |
Delete the DTCs (Click here).
Recheck for DTCs (Click here).
- HINT:
- If DTCs are detected frequently, replace the ECU.
- OK:
- DTC is not output.
|
|
||||
| OK | ||
| ||
| 11. CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY) |
Disconnect the Q12 and Q1 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Q12-2 (E) - Q1-2 (GND)
Always
Below 1 Ω
Q12-7 (OPN) - Q1-4 (OPN)
Always
Below 1 Ω
Q12-8 (DWN) - Q1-5 (DOWN)
Always
Below 1 Ω
Q12-9 (CLS) - Q1-3 (CLS)
Always
Below 1 Ω
Q12-10 (UP) - Q1-6 (UP)
Always
Below 1 Ω
Q1-3 (CLS) - Body ground
Always
10 kΩ or higher
Q1-4 (OPN) - Body ground
Always
10 kΩ or higher
Q1-2 (GND) - Body ground
Always
Below 1 Ω
Q1-5 (DOWN) - Body ground
Always
10 kΩ or higher
Q1-6 (UP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
