2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION


w/o Multi-information Display:
The clock assembly uses this circuit to receive the illumination signal via the direct line. The combination meter assembly controls illumination through the ILL+ terminal.

w/ Multi-information Display:
The clock assembly uses this circuit to receive the auto dimmer signal and tail cancel signal. When the clock assembly receives an auto dimmer signal from the main body ECU through the combination meter assembly via the direct line, the combination meter assembly causes the clock display to be dimmed. When the meter CPU receives an auto dimmer signal, it dims the meter illumination and clock illumination. The main body ECU determines whether it is daytime, twilight, or nighttime based on the waveform transmitted from the automatic light control sensor. If the main body ECU determines that it is daytime, the ECU does not send auto dimmer signals. Therefore, the clock illumination (multi-information display) will not dim even if the driver accidentally turns the light control switch to the TAIL or HEAD position in daytime.

HINT:
If the automatic light control sensor has a malfunction, DTC B1244 is output. (Click here)


WIRING DIAGRAM


w/o Multi-information Display:
E152410E01

w/ Multi-information Display:
E175148E01

INSPECTION PROCEDURE


1. CONFIRM SYMPTOMS
  1. Confirm the symptom.

    Result:
    Result
    Proceed to
    Only clock illumination has a malfunction.
    A
    Clock illumination, combination meter assembly illumination, and heater control panel illumination have a malfunction.
    B



B
GO TO METER / GAUGE SYSTEM (Click here)
A


2. SYSTEM CHECK
  1. Confirm the vehicle model.

    Result:
    Result
    Proceed to
    w/o Multi-information Display
    A
    w/ Multi-information Display
    B



B
Go to step 5
A


3. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER)

  1. E152412E01
    Disconnect E1 and E20 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E20-3 (ILL+) - E1-30 (ILL-)
    Always
    Below 1 Ω
    E1-30 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT CLOCK ASSEMBLY

  1. E146920E05
    Reconnect the E20 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E1-30 (ILL-) - Body ground
    Ignition switch on (IG), headlight dimmer switch TAIL or HEAD
    11 to 14 V
    E1-30 (ILL-) - Body ground
    Ignition switch on (IG), headlight dimmer switch OFF
    Below 1 V



NG
REPLACE CLOCK ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK CAN COMMUNICATION SYSTEM
  1. Check if any DTC is output (Click here).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN Communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


6. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check the clock illumination.

    Main Body:
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Dimmer Signal
    Dimmer Signal
    Dimmer signal is OFF/ON
    Confirm that the vehicle is stopped, engine idling

    OK:
    The clock illumination is dimmed when the Dimmer signal is ON.

    HINT:
    Refer to the sensitivity setting in the customization table of the lighting system (Click here).



NG
Go to step 7
OK

GO TO LIGHTING SYSTEM (Click here)

7. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER)

  1. E152378E10
    Disconnect the E1 and E9 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-9 (CLK) - E1-36 (MCLK)
    Always
    Below 1 Ω
    E9-10 (DATA) - E1-37 (MDAT)
    Always
    Below 1 Ω
    E9-11 (SYNC) - E1-38 (SYNC)
    Always
    Below 1 Ω
    E1-36 (MCLK) - Body ground
    Always
    10 kΩ or higher
    E1-37 (MDAT) - Body ground
    Always
    10 kΩ or higher
    E1-38 (SYNC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT COMBINATION METER ASSEMBLY

  1. E146936E20
    Reconnect the E1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E9-9 (CLK) - Body ground
    Ignition switch on (IG), headlight dimmer switch TAIL or HEAD
    Pulse generation
    E9-10 (DATA) - Body ground
    Ignition switch on (IG), headlight dimmer switch TAIL or HEAD
    Pulse generation
    E9-11 (SYNC) - Body ground
    Ignition switch on (IG), headlight dimmer switch TAIL or HEAD
    Pulse generation
    E9-9 (CLK) - Body ground
    Ignition switch on (IG), headlight dimmer switch OFF
    Below 1 V
    E9-10 (DATA) - Body ground
    Ignition switch on (IG), headlight dimmer switch OFF
    Below 1 V
    E9-11 (SYNC) - Body ground
    Ignition switch on (IG), headlight dimmer switch OFF
    Below 1 V



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CLOCK ASSEMBLY (Click here)


← Illumination Circuit (May 2007 – Jul 2008)Illumination Circuit (Jul 2010 – Jun 2012) →