Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM
Starter Signal Circuit
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly to the park/neutral position switch assembly and also flows to terminal STA of the ECM (STA Signal). WIRING DIAGRAM
Refer to DTC P0617 (Click here ). INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
This diagnosis procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (Click here ).
1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to ON and engine cranking position.
OK:
Ignition Switch Position
Starter Signal
Ignition switch on (IG)
Close (starter signal off)
Engine cranking position
Open (starter signal on)
NG
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here )
2. CHECK ST RELAY (POWER SOURCE)
Remove the ST relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
ST relay terminal 2 - Body ground
Engine cranking position
11 to 14 V
Text in Illustration
*1
Engine Room Relay Block
HINT:
The engine will not crank because the relay is not installed.
Reinstall the ST relay.
Result:
Result
Proceed to
OK
A
NG (A/T models)
B
NG (M/T models)
C
NG
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)
3. CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
Remove the ST relay from the engine room relay block.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
ST relay terminal 2 - B5-5
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
ST relay terminal 2 or B5-5 - Body ground
Always
10 kΩ or higher
Reinstall the ST relay.
Reconnect the park/neutral position switch assembly connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
OK
4. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Inspect the park/neutral position switch assembly (Click here for U151E, Click here for U151F).
Result:
Result
Proceed to
OK
A
NG (for U151E)
B
NG (for U151F)
C
B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here )
C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here )
A
5. CHECK HARNESS AND CONNECTOR
Disconnect the ECM connector.
Disconnect the ignition switch assembly connector.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B42-2 (NSW) - D21-3 (ST1)
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B42-2 (NSW) or D21-3 (ST1) or B5-4 - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the ignition switch assembly connector.
Reconnect the park/neutral position switch assembly connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
Disconnect the ECM connector.
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B5-5 or D55-10 (STA) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the park/neutral position switch assembly connector.
Reinstall the ST relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
OK
7. INSPECT IGNITION SWITCH ASSEMBLY
Inspect the ignition switch assembly (Click here ).
NG
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)