C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Also covers:
- C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
DTCs C1273 to C1278 will be deleted when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs from C1273 to C1278 are output only in Test Mode.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1273 C1274 |
Detected only during Test Mode. |
|
| C1277 C1278 |
Detected only during Test Mode. |
Speed sensor rotor |
- HINT:
- DTCs C1273 and C1277 are for the rear speed sensor RH.
- DTCs C1274 and C1278 are for the rear speed sensor LH.
- DTCs C1273 and C1277 are for the rear speed sensor RH.
WIRING DIAGRAM
Refer to DTCs C1403 and C1404 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
RR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RL Speed Open
RL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
- Result:
Result
Proceed to
There are momentary interruptions
A
There are no momentary interruptions
B
There is a constant open circuit
C
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
|
|
||||
| A | |
| 2. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and the rear speed sensor (Click here).
Check that there are no momentary interruptions.
| NEXT | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 4. READ VALUE ON INTELLIGENT TESTER (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
RL Wheel Speed
RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 5. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 6. CHECK REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.

Check the speed sensor installation (for 2WD).
- OK:
- There is no clearance between the sensor and the rear axle carrier.
Check the speed sensor installation (for 4WD).
- OK:
- There is no clearance between the sensor and the rear axle carrier.
- The installation nut is tightened properly.
- Torque:
- 8.0 N*m (82 kgf*cm, 71 in.*lbf)
- Result:
Result
Proceed to
OK (for 4WD)
A
OK (for 2WD)
B
NG (for 2WD)
C
NG (for 4WD)
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 7. CHECK REAR SPEED SENSOR TIP |
Remove the rear speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | |
| 8. CHECK REAR SPEED SENSOR ROTOR |
Remove the rear speed sensor rotor (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
- HINT:
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
|
|
||||
| OK | |
| 9. INSPECT REAR SPEED SENSOR |
Install the rear speed sensor and the rear speed sensor rotor.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for 2WD RH:
Tester Connection
Condition
Specified Condition
2 (RR+) - Body ground
Always
10 kΩ or higher
1 (RR-) - Body ground
Always
10 kΩ or higher
- for 4WD RH:
Tester Connection
Condition
Specified Condition
1 (RR+) - Body ground
Always
10 kΩ or higher
2 (RR-) - Body ground
Always
10 kΩ or higher
- for 2WD LH:
Tester Connection
Condition
Specified Condition
2 (RL+) - Body ground
Always
10 kΩ or higher
1 (RL-) - Body ground
Always
10 kΩ or higher
- for 4WD LH:
Tester Connection
Condition
Specified Condition
1 (RL+) - Body ground
Always
10 kΩ or higher
2 (RL-) - Body ground
Always
10 kΩ or higher
- Result:
Result
Proceed to
OK (for 2WD)
A
OK (for 4WD)
B
NG (for 2WD)
C
NG (for 4WD)
D
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
|
|
||||
|
|
||||
| A | |
| 10. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.

Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for RH:
Tester Connection
Condition
Specified Condition
z10 ("A"-2) - z10 ("B"-1)
Always
Below 1 Ω
z10 ("A"-2) - z10 ("B"-2)
Always
10 kΩ or higher
z10 ("A"-2) - Body ground
Always
10 kΩ or higher
z10 ("A"-1) - z10 ("B"-2)
Always
Below 1 Ω
z10 ("A"-1) - z10 ("B"-1)
Always
10 kΩ or higher
z10 ("A"-1) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
z9 ("A"-2) - z9 ("B"-1)
Always
Below 1 Ω
z9 ("A"-2) - z9 ("B"-2)
Always
10 kΩ or higher
z9 ("A"-2) - Body ground
Always
10 kΩ or higher
z9 ("A"-1) - z9 ("B"-2)
Always
Below 1 Ω
z9 ("A"-1) - z9 ("B"-1)
Always
10 kΩ or higher
z9 ("A"-1) - Body ground
Always
10 kΩ or higher
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Reconnect the skid control sensor wire (for 2WD).

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for 2WD RH:
Tester Connection
Condition
Specified Condition
A24-17 (RR+) - z10-2 (RR+)
Always
Below 1 Ω
A24-17 (RR+) - Body ground
Always
10 kΩ or higher
A24-16 (RR-) - z10-1 (RR-)
Always
Below 1 Ω
A24-16 (RR-) - Body ground
Always
10 kΩ or higher
- for 4WD RH:
Tester Connection
Condition
Specified Condition
A24-17 (RR+) - N22-1 (RR+)
Always
Below 1 Ω
A24-17 (RR+) - Body ground
Always
10 kΩ or higher
A24-16 (RR-) - N22-2 (RR-)
Always
Below 1 Ω
A24-16 (RR-) - Body ground
Always
10 kΩ or higher
- for 2WD LH:
Tester Connection
Condition
Specified Condition
A24-5 (RL+) - z9-2 (RL+)
Always
Below 1 Ω
A24-5 (RL+) - Body ground
Always
10 kΩ or higher
A24-4 (RL-) - z9-1 (RL-)
Always
Below 1 Ω
A24-4 (RL-) - Body ground
Always
10 kΩ or higher
- for 4WD LH:
Tester Connection
Condition
Specified Condition
A24-5 (RL+) - O40-1 (RL+)
Always
Below 1 Ω
A24-5 (RL+) - Body ground
Always
10 kΩ or higher
A24-4 (RL-) - O40-2 (RL-)
Always
Below 1 Ω
A24-4 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 12. INSPECT SKID CONTROL ECU (SENSOR INPUT) |
Reconnect the skid control ECU connector.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- for 2WD RH:
Tester Connection
Switch Condition
Specified Condition
z10-2 (RR+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for 4WD RH:
Tester Connection
Switch Condition
Specified Condition
N22-1 (RR+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for 2WD LH:
Tester Connection
Switch Condition
Specified Condition
z9-2 (RL+) - Body ground
Ignition switch on (IG)
8 to 14 V
- for 4WD LH:
Tester Connection
Switch Condition
Specified Condition
O40-1 (RL+) - Body ground
Ignition switch on (IG)
8 to 14 V
|
|
||||
| OK | |
| 13. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
- Result:
Result
Proceed to
OK
A
NG (for 2WD)
B
NG (for 4WD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 14. REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
Replace the rear axle hub and bearing assembly (rear speed sensor rotor) (Click here).
- HINT:
- The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 15. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 16. REPLACE REAR SPEED SENSOR |
Turn the ignition switch off.
Replace the rear speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 17. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
| 18. REPLACE REAR SPEED SENSOR ROTOR |
Turn the ignition switch off.
Replace the rear drive shaft assembly (rear speed sensor rotor) (Click here).
- HINT:
- If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 19. PERFORM TEST MODE (SIGNAL CHECK) |
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are erased.
|
|
||||
| OK | ||
| ||
