2007-2013 Highlander Kluger · Service Manual BRAKE

C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

DTCs C1273 to C1278 will be deleted when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs from C1273 to C1278 are output only in Test Mode.
DTC Code
DTC Detection Condition
Trouble Area
C1273
C1274
Detected only during Test Mode.
  1. Rear speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor
C1277
C1278
Detected only during Test Mode.
Speed sensor rotor

HINT:
  1. DTCs C1273 and C1277 are for the rear speed sensor RH.
  2. DTCs C1274 and C1278 are for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1403 and C1404 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    Result:
    Result
    Proceed to
    There are momentary interruptions
    A
    There are no momentary interruptions
    B
    There is a constant open circuit
    C

    HINT:
    Perform the above inspection before removing the sensor and connector.



B
Go to step 4

C
Go to step 6
A


2. REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU and the rear speed sensor (Click here).

  1. Check that there are no momentary interruptions.


NEXT


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
Go to step 4
OK

END

4. READ VALUE ON INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

ABS / VSC / TRC: 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Direction
RR wheel direction / FORWARD or BACK
FORWARD: Forward
BACK: Back
-
RL Wheel Direction
RL wheel direction / FORWARD or BACK
FORWARD: Forward
BACK: Back
-
  1. Check that the sensor signal conforms to the wheel direction.

    OK:
    The wheel direction is displayed.



NG
Go to step 6
OK


5. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
Go to step 6
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

6. CHECK REAR SPEED SENSOR INSTALLATION

  1. C168820E01
    Turn the ignition switch off.

  1. Check the speed sensor installation (for 2WD).

    OK:
    There is no clearance between the sensor and the rear axle carrier.

  1. Check the speed sensor installation (for 4WD).

    OK:
    There is no clearance between the sensor and the rear axle carrier.
    The installation nut is tightened properly.
    Torque:
    8.0 N*m (82 kgf*cm, 71 in.*lbf)


    Result:
    Result
    Proceed to
    OK (for 4WD)
    A
    OK (for 2WD)
    B
    NG (for 2WD)
    C
    NG (for 4WD)
    D



B
Go to step 9

C
INSTALL REAR SPEED SENSOR CORRECTLY (for 2WD) (Click here)

D
INSTALL REAR SPEED SENSOR CORRECTLY (for 4WD) (Click here)
A


7. CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


8. CHECK REAR SPEED SENSOR ROTOR
  1. Remove the rear speed sensor rotor (Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

    HINT:
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.



NG
CLEAN OR REPLACE REAR SPEED SENSOR ROTOR
OK


9. INSPECT REAR SPEED SENSOR

  1. C168821E02
    Install the rear speed sensor and the rear speed sensor rotor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2WD RH:
    Tester Connection
    Condition
    Specified Condition
    2 (RR+) - Body ground
    Always
    10 kΩ or higher
    1 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 4WD RH:
    Tester Connection
    Condition
    Specified Condition
    1 (RR+) - Body ground
    Always
    10 kΩ or higher
    2 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 2WD LH:
    Tester Connection
    Condition
    Specified Condition
    2 (RL+) - Body ground
    Always
    10 kΩ or higher
    1 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 4WD LH:
    Tester Connection
    Condition
    Specified Condition
    1 (RL+) - Body ground
    Always
    10 kΩ or higher
    2 (RL-) - Body ground
    Always
    10 kΩ or higher


    Result:
    Result
    Proceed to
    OK (for 2WD)
    A
    OK (for 4WD)
    B
    NG (for 2WD)
    C
    NG (for 4WD)
    D

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



B
Go to step 11

C
REPLACE REAR SPEED SENSOR (for 2WD) (Click here)

D
REPLACE REAR SPEED SENSOR (for 4WD) (Click here)
A


10. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

  1. C169030E02
    Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    z10 ("A"-2) - z10 ("B"-1)
    Always
    Below 1 Ω
    z10 ("A"-2) - z10 ("B"-2)
    Always
    10 kΩ or higher
    z10 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    z10 ("A"-1) - z10 ("B"-2)
    Always
    Below 1 Ω
    z10 ("A"-1) - z10 ("B"-1)
    Always
    10 kΩ or higher
    z10 ("A"-1) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    z9 ("A"-2) - z9 ("B"-1)
    Always
    Below 1 Ω
    z9 ("A"-2) - z9 ("B"-2)
    Always
    10 kΩ or higher
    z9 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    z9 ("A"-1) - z9 ("B"-2)
    Always
    Below 1 Ω
    z9 ("A"-1) - z9 ("B"-1)
    Always
    10 kΩ or higher
    z9 ("A"-1) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

  1. C169033E03
    Reconnect the skid control sensor wire (for 2WD).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2WD RH:
    Tester Connection
    Condition
    Specified Condition
    A24-17 (RR+) - z10-2 (RR+)
    Always
    Below 1 Ω
    A24-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-16 (RR-) - z10-1 (RR-)
    Always
    Below 1 Ω
    A24-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 4WD RH:
    Tester Connection
    Condition
    Specified Condition
    A24-17 (RR+) - N22-1 (RR+)
    Always
    Below 1 Ω
    A24-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-16 (RR-) - N22-2 (RR-)
    Always
    Below 1 Ω
    A24-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 2WD LH:
    Tester Connection
    Condition
    Specified Condition
    A24-5 (RL+) - z9-2 (RL+)
    Always
    Below 1 Ω
    A24-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-4 (RL-) - z9-1 (RL-)
    Always
    Below 1 Ω
    A24-4 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 4WD LH:
    Tester Connection
    Condition
    Specified Condition
    A24-5 (RL+) - O40-1 (RL+)
    Always
    Below 1 Ω
    A24-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-4 (RL-) - O40-2 (RL-)
    Always
    Below 1 Ω
    A24-4 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. INSPECT SKID CONTROL ECU (SENSOR INPUT)

  1. C169034E03
    Reconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for 2WD RH:
    Tester Connection
    Switch Condition
    Specified Condition
    z10-2 (RR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 4WD RH:
    Tester Connection
    Switch Condition
    Specified Condition
    N22-1 (RR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 2WD LH:
    Tester Connection
    Switch Condition
    Specified Condition
    z9-2 (RL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 4WD LH:
    Tester Connection
    Switch Condition
    Specified Condition
    O40-1 (RL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


13. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.


    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2WD)
    B
    NG (for 4WD)
    C



B
Go to step 14

C
Go to step 16
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

14. REPLACE REAR SPEED SENSOR AND REAR SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).

  1. Replace the rear axle hub and bearing assembly (rear speed sensor rotor) (Click here).

    HINT:
    The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


15. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

END

16. REPLACE REAR SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


17. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
Go to step 18
OK

END

18. REPLACE REAR SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear drive shaft assembly (rear speed sensor rotor) (Click here).

    HINT:
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


19. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

END


← C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) (+ C1272, C1275, C1276) (from Jul 2010)C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) (+ C1274, C1277, C1278) (Aug 2008 – Jun 2010) →