2007-2013 Highlander Kluger · Service Manual BRAKE

C1415 Rear Speed Sensor RH Output Malfunction

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.
C172030E01
DTC Code
DTC Detection Condition
Trouble Area
C1415
C1416
Any of the following is detected:
  1. An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.
  2. At a vehicle speed 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.
  3. At a vehicle speed 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor RH/LH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Brake actuator assembly (Skid control ECU)

HINT:
  1. DTC C1415 is for the rear speed sensor RH.
  2. DTC C1416 is for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1403 and C1404 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. READ VALUE ON INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    RL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs (C1415 and C1416) are not output
    A
    DTCs (C1415 and/or C1416) are output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

4. CHECK REAR SPEED SENSOR INSTALLATION

  1. C168820E01
    Turn the ignition switch off.

  1. Check the speed sensor installation (for 2WD).

    OK:
    There is no clearance between the sensor and the rear axle carrier.

  1. Check the speed sensor installation (for 4WD).

    OK:
    There is no clearance between the sensor and the rear axle carrier.
    The installation nut is tightened properly.
    Torque:
    8.0 N*m (82 kgf*cm, 71 in.*lbf)


    Result:
    Result
    Proceed to
    OK (for 4WD)
    A
    OK (for 2WD)
    B
    NG (for 2WD)
    C
    NG (for 4WD)
    D



B
Go to step 7

C
INSTALL REAR SPEED SENSOR CORRECTLY (for 2WD) (Click here)

D
INSTALL REAR SPEED SENSOR CORRECTLY (for 4WD) (Click here)
A


5. CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


6. CHECK REAR SPEED SENSOR ROTOR
  1. Remove the rear speed sensor rotor (Click here).

  1. Check the speed sensor rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.


    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

    HINT:
    If the rear speed sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.



B
Go to step 8
A

CLEAN OR REPLACE REAR SPEED SENSOR ROTOR

7. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

  1. C169030E02
    Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    z10 ("A"-2) - z10 ("B"-1)
    Always
    Below 1 Ω
    z10 ("A"-2) - z10 ("B"-2)
    Always
    10 kΩ or higher
    z10 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    z10 ("A"-1) - z10 ("B"-2)
    Always
    Below 1 Ω
    z10 ("A"-1) - z10 ("B"-1)
    Always
    10 kΩ or higher
    z10 ("A"-1) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    z9 ("A"-2) - z9 ("B"-1)
    Always
    Below 1 Ω
    z9 ("A"-2) - z9 ("B"-2)
    Always
    10 kΩ or higher
    z9 ("A"-2) - Body ground
    Always
    10 kΩ or higher
    z9 ("A"-1) - z9 ("B"-2)
    Always
    Below 1 Ω
    z9 ("A"-1) - z9 ("B"-1)
    Always
    10 kΩ or higher
    z9 ("A"-1) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

  1. C169033E03
    Install the rear speed sensor and the rear speed sensor rotor.

  1. Reconnect the skid control sensor wire (for 2WD).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector and the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for 2WD RH:
    Tester Connection
    Condition
    Specified Condition
    A24-17 (RR+) - z10-2 (RR+)
    Always
    Below 1 Ω
    A24-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-16 (RR-) - z10-1 (RR-)
    Always
    Below 1 Ω
    A24-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 4WD RH:
    Tester Connection
    Condition
    Specified Condition
    A24-17 (RR+) - N22-1 (RR+)
    Always
    Below 1 Ω
    A24-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A24-16 (RR-) - N22-2 (RR-)
    Always
    Below 1 Ω
    A24-16 (RR-) - Body ground
    Always
    10 kΩ or higher
    for 2WD LH:
    Tester Connection
    Condition
    Specified Condition
    A24-5 (RL+) - z9-2 (RL+)
    Always
    Below 1 Ω
    A24-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-4 (RL-) - z9-1 (RL-)
    Always
    Below 1 Ω
    A24-4 (RL-) - Body ground
    Always
    10 kΩ or higher
    for 4WD LH:
    Tester Connection
    Condition
    Specified Condition
    A24-5 (RL+) - O40-1 (RL+)
    Always
    Below 1 Ω
    A24-5 (RL+) - Body ground
    Always
    10 kΩ or higher
    A24-4 (RL-) - O40-2 (RL-)
    Always
    Below 1 Ω
    A24-4 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT SKID CONTROL ECU (SENSOR INPUT)

  1. C169034E03
    Reconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for 2WD RH:
    Tester Connection
    Switch Condition
    Specified Condition
    z10-2 (RR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 4WD RH:
    Tester Connection
    Switch Condition
    Specified Condition
    N22-1 (RR+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 2WD LH:
    Tester Connection
    Switch Condition
    Specified Condition
    z9-2 (RL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V
    for 4WD LH:
    Tester Connection
    Switch Condition
    Specified Condition
    O40-1 (RL+) - Body ground
    Ignition switch on (IG)
    8 to 14 V


    Result:
    Result
    Proceed to
    OK (for 2WD)
    A
    OK (for 4WD)
    B
    NG
    C

    NOTICE:
    Check the speed sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE REAR SPEED SENSOR (for 4WD) (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPLACE REAR SPEED SENSOR (for 2WD) (Click here)


← C1415 Rear Speed Sensor RH Output Malfunction (+ C1416) (May 2007 – Jul 2008)C1415 Rear Speed Sensor RH Output Malfunction (+ C1416) (from Jul 2010) →