2007-2013 Highlander Kluger · Service Manual BODY

Power Back Door Warning System does not Operate

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the power back door warning system does not operate, one of the following may be malfunctioning: 1) power back door warning buzzer circuit, 2) wireless door lock control system, or 3) power back door drive unit (power back door ECU).

WIRING DIAGRAM

B165222E04

INSPECTION PROCEDURE


1. CHECK OPERATION
  1. Check the power back door system operation.

    Result:
    Result
    Proceed to
    Power back door warning buzzer does not operate.
    A
    Hazard warning light does not come on.
    B
    Power back door warning buzzer in the power back door ECU does not operate.
    C



B
Go to step 5

C
REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)
A


2. PERFORM ACTIVE TEST ON INTELLIGENT TESTER
  1. Select the Active Test, use the intelligent tester to generate a control command, and check that the power back door buzzer sounds.

    Back door (Power back door ECU) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    PBD Buzzer
    Power back door buzzer sound
    ON / OFF
    -

    OK:
    Buzzer sounds normally.



NG
Go to step 3
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)

3. INSPECT POWER BACK DOOR WARNING BUZZER

  1. B177974E01
    Remove the power back door warning buzzer. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    950 to 1050 Ω



NG
REPLACE POWER BACK DOOR WARNING BUZZER (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR WARNING BUZZER - POWER BACK DOOR ECU)

  1. B165206E03
    Disconnect the T9 buzzer connector.

  1. Disconnect the O14 ECU connector.

  1. Disconnect the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T9-1 - O14-26 (BZR+)
    Always
    Below 1 Ω
    T9-2 - Body ground
    Always
    Below 1 Ω
    T9-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)

5. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM (HAZARD ANSWER-BACK FUNCTION)
  1. Check the wireless door lock operation.

    Result:
    Result
    Proceed to
    Hazard answer-back function operate normally.
    A
    Hazard answer-back function does not operate. (w/o Smart Entry and Start System)
    B
    Hazard answer-back function does not operate. (w/ Smart Entry and Start System)
    C



B
GO TO OTHER FLOW CHART (No Answer-Back (w/o Smart Entry and Start System)) (Click here)

C
GO TO OTHER FLOW CHART (No Answer-Back (w/ Smart Entry and Start System)) (Click here)
A


6. REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Replace the power back door drive unit (power back door ECU) (Click here).


NEXT


7. CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
  1. Check that the power back door warning buzzer operates normally.

    OK:
    It operates normally.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

END (REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) DEFECTIVE)


← Power Back Door Warning System does not Operate (May 2007 – Jul 2008)Power Back Door Warning System does not Operate (from Jul 2010) →