Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

DTC    P0174    System Too Lean (Bank 2)

DTC    P0175    System Too Rich (Bank 2)

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short- term fuel trim compensation.
If both the short-term and long-term fuel trims are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and sets a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0171
P0174
With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
  1. Air induction system
  2. Injector blockage
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  8. Air fuel ratio sensor (bank 1, 2 sensor 1)
  9. EFI NO. 2 fuse
  10. PCV valve and hose
  11. PCV hose connections
  12. ECM
P0172
P0175
With warm engine and stable air fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
  1. Injector leak or blockage
  2. Mass air flow meter
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  8. Air fuel ratio sensor (bank 1, 2 sensor 1)
  9. EFI NO. 2 fuse
  10. ECM

HINT:
  1. When DTC P0171 or P0174 is set, the actual air fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this a fault in the fuel system and sets a DTC.
Example:
The average fuel trim learning value is more than +35% or less than -35%, the ECM interprets this as a fuel system malfunction.

A121607E14


MONITOR STRATEGY


Related DTCs
P0171: Fuel trim Lean (bank 1)
P0172: Fuel trim Rich (bank 1)
P0174: Fuel trim Lean (bank 2)
P0175: Fuel trim Rich (bank 2)
Required Sensors/Components (Main)
Fuel system
Required Sensors/Components (Related)
Air fuel ratio sensor
Mass air flow meter
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
Less than 10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Fuel-trim: 
The monitor will run whenever these DTCs are not present
P0010, P0020 (OCV bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust OCV bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (A/F sensor heater)
P0100, P0102, P0103 (MAF meter)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0335 (CKP sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
Fuel system status
Closed-loop
Battery voltage
11 V or more
Either of following conditions 1 or 2 set
-
1. Engine RPM
Less than 1100 rpm
2. Intake air amount per revolution
0.22 g/rev or more
Catalyst monitor
No executed

TYPICAL MALFUNCTION THRESHOLDS


Fuel-trim: 
Purge-cut
Executing
Either of following conditions 1 or 2 met
-
1. Average between short-term fuel trim and long-term fuel trim
35% or more (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim
-35% or less (varies with engine coolant temperature)

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Start the engine.
  3. Turn the tester on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  6. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  7. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1 S1 or AFS Voltage B2 S1 and O2S B1 S2 or O2S B2 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Tester Display
Injection Volume
Status
Voltage
AFS Voltage B1 S1
AFS Voltage B2 S1
(Air fuel ratio sensor)
+25%
Rich
Less than 3.1 V
-12.5%
Lean
More than 3.5 V
O2S B1 S2
O2S B2 S2
(Heated oxygen)
+25%
Rich
More than 0.55 V
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A162605E07
A162598E03
-
2
A162596E03
A162598E03
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E07
A162596E03
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A162596E03
A162596E03
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (Air fuel ratio extremely lean or rich)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, select the following menu items:
    Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1 S1 or AFS Voltage B2 S1 and O2S B1 S2 or O2S B2 S2; then press the graph button on the Data List view.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0171, P0172, P0174 or P0175
    A
    P0171, P0172, P0174 or P0175 and other DTCs
    B

    HINT:
    If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak (Click here).

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (AIR FUEL RATIO CONTROL)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1 S1 or AFS Voltage B2 S1 and O2S B1 S2 or O2S B2 S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


    Standard:

    Tester Display
    Injection Volume
    Status
    Voltage
    AFS Voltage B1 S1
    AFS Voltage B2 S1
    (Air fuel ratio sensor)
    +25%
    Rich
    Less than 3.1 V
    -12.5%
    Lean
    More than 3.5 V
    O2S B1 S2
    O2S B2 S2
    (Heated oxygen)
    +25%
    Rich
    More than 0.55 V
    -12.5%
    Lean
    Less than 0.4 V


    Result 
    Status
    AFS B1 S1
    AFS B2 S1
    Status
    O2S B1 S2
    O2S B2 S2
    Air Fuel Ratio Condition and
    Air Fuel Ratio Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    C
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Injector blockage
    4. Gas leak from exhaust system
    5. Air induction system
    6. Fuel pressure
    7. Mass air flow meter
    8. Engine coolant temperature sensor
    A
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Injector blockage or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter
    6. Engine coolant temperature sensor
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS) is consistently more than 3.5 V, and the heated oxygen sensor output voltage (O2S) is consistently less than 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



B
Go to step 11

C
Go to step 15
A


5.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard value:
    With cold engine: Same as ambient air temperature.
    With warm engine: 80 to 100°C (176 to 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6.INSPECT MASS AIR FLOW METER
  1. Read the values using the Techstream (mass air flow).

    NOTICE:
    1. Turn the ignition switch off.
    2. Perform the inspection with the vehicle indoors and on a level surface.
    3. Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
    4. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

    1. Turn the ignition switch on (IG) (do not start the engine).

    2. Turn the tester on.

    3. Select the following menu items: Select: Powertrain / Engine and ECT / Data List / MAF.

    4. Wait for 30 seconds, and read the values on the tester.

      Standard value:
      Less than 0.70 g/sec



  1. Inspect the mass air flow meter.

    1. Remove the mass air flow meter (Click here).



    2. A154164E03
    3. Using a work light, check that the platinum filament (heater portion) in the mass air flow meter has no foreign matter attached.

      OK:
      No foreign matter attached.

    4. Reinstall the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK SPARK AND IGNITION

HINT:
  1. Refer to the ignition system inspection procedure (Click here).
  2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Select the following menu items: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Rate (to Cylinder #6 Misfire Rate)



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

HINT:
  1. Refer to the fuel injector inspection procedure (Click here).
  2. If the injectors malfunction, engine misfire may occur. The misfire count can be read using the Techstream. Select the following menu items: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Rate (to Cylinder #6 Misfire Rate).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A126269E40
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)


    A168194E01
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    B20-2 (+B) - Body ground
    Ignition switch on (IG)
    9 to 14 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B19-2 (+B) - Body ground
    Ignition switch on (IG)
    9 to 14 V

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 17
OK


13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)


    A168195E04
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B2-2 (HA1A)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) - B2-1 (HA2A)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B2-2 (HA1A) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) or B2-1 (HA2A) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN


  1. A162663E09

  2. (a) Connect the Techstream to the DLC3.
  3. (b) Turn the ignition switch on (IG).
  4. (c) Turn the tester on.
  5. (d) Clear DTCs (Click here).
  6. (e) Switch the ECM from normal mode to check mode using the tester (Click here).
  7. (f) Start the engine and warm it up with all the accessories switched OFF.
  8. (g) Drive the vehicle at between 40 mph and 75 mph (64 km/h and 120 km/h) and at an engine speed of between 1400 rpm and 3200 rpm for 3 to 5 minutes.

    HINT:
    If the system is still malfunctioning, the MIL will be illuminated during step (g).

    NOTICE:
    If the conditions in this test are not strictly followed, no malfunction will be detected.


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171, P0172, P174 OR P0175)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P0171, P0172, P0174 or P0175
    B



B
REPLACE ECM (Click here)
A

END 

17.INSPECT FUSE (A/F FUSE)


    A168235E01
  1. Remove the A/F fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A/F fuse
    Always
    Below 1 Ω

  1. Reinstall the A/F fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


18.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (A/F RELAY)
  1. Inspect the A/F relay (Click here).



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO FUSE - AIR FUEL RATIO SENSOR)