Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation has been disabled.

HINT:
For vehicles with the multi-information display, the master caution indicator light will come on and a brake malfunction message will be displayed on the multi-information display if the EBD system is malfunctioning.


WIRING DIAGRAM


C171171E03


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (for 2GR-FE) (Click here)
OK


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)


    C160263E43
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-34 (IG1) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND1 TERMINAL)


    C160263E41
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6.READ VALUE ON TECHSTREAM (PARKING BRAKE SWITCH)
  1. Reconnect the skid control ECU connector.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using Techstream, check the switch condition on Techstream changes according to parking brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to parking brake pedal operation.



NG
Go to step 10
OK


7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C156508E01
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (E)
    Brake fluid level warning switch OFF (Float up)
    1.9 to 2.1 kΩ
    1 (+) - 2 (E)
    Brake fluid level warning switch ON (Float down)
    Below 1 Ω

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)


    C158617E07
  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-28 (B/LE) - A21-1 (+)
    Always
    Below 1 Ω
    E1-28 (B/LE) - Body ground
    Always
    10 kΩ or higher
    A21-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT COMBINATION METER ASSEMBLY
  1. Perform the Active Test of the combination meter (meter CPU) using Techstream (Click here).

  1. Check the combination meter.

    HINT:
    Reinstall the connectors and restore the vehicle to its prior condition before checking the combination meter.

    OK:
    The brake warning light turns on or off in accordance with Techstream operation.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

10.INSPECT PARKING BRAKE SWITCH


    C167308E01
  1. Turn the ignition switch off.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)


    C167309E02
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-29 (PKB) - A17-1
    Always
    Below 1 Ω
    A24-29 (PKB) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)