Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B in CAN bus wire
  2. Skid control ECU
  3. Power steering ECU
  4. Steering angle sensor
  5. Yaw rate sensor
  6. ECM
  7. Center airbag sensor assembly
  8. Air conditioning amplifier
  9. Combination meter ECU
  10. Main body ECU
  11. Accessory gateway
  12. CAN junction connector CTR
  13. CAN junction connector RH

WIRING DIAGRAM


C170106E03


C170107E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If the doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)
  1. Turn the ignition switch off, and disconnect negative battery terminal.

  1. Disconnect the CAN junction connector CTR.



  1. Measure the resistance according to the value(s) in the table below.


    C170177E01


    Standard resistance:

    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D55-1 (CANH) - D47-16 (BAT)
    SB - LG
    CAN junction connector RH
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-12 (CANL) - D47-16 (BAT)
    W - LG
    CAN junction connector RH
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-4 (CANH) - D47-16 (BAT)
    L - LG
    DLC3
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-15 (CANL) - D47-16 (BAT)
    W - LG
    DLC3
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-6 (CANH) - D47-16 (BAT)
    P - LG
    Combination meter
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-17 (CANL) - D47-16 (BAT)
    W - LG
    Combination meter
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (DLC3 branch wire)
    B
    NG (Combination meter main wire)
    C
    NG (CAN junction connector RH main wire)
    D



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3

C
Go to step 4

D
Go to step 5
A


2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)


  1. Measure the resistance according to the value(s) in the table below.


    C170177E02


    Standard resistance:

    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D55-2 (CANH) - D47-16 (BAT)
    V - LG
    Yaw rate sensor
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-13 (CANL) - D47-16 (BAT)
    W - LG
    Yaw rate sensor
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-3 (CANH) - D47-16 (BAT)
    Y - LG
    Center airbag sensor assembly
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-14 (CANL) - D47-16 (BAT)
    W - LG
    Center airbag sensor assembly
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-5 (CANH) - D47-16 (BAT)
    R - LG
    Steering angle sensor
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-16 (CANL) - D47-16 (BAT)
    W - LG
    Steering angle sensor
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Yaw rate sensor branch wire)
    B
    NG (Center airbag sensor assembly branch wire)
    C
    NG (Steering angle sensor branch wire)
    D



B
Go to step 8

C
Go to step 9

D
Go to step 10
A


3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR CTR)


  1. Measure the resistance according to the value(s) in the table below.


    C170177E03


    Standard resistance:

    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D55-7 (CANH) - D47-16 (BAT)
    BR - LG
    Power steering ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-18 (CANL) - D47-16 (BAT)
    W - LG
    Power steering ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-8 (CANH) - D47-16 (BAT)
    GR - LG
    Main body ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-19 (CANL) - D47-16 (BAT)
    W - LG
    Main body ECU
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Power steering ECU branch wire)
    B
    NG (Main body ECU branch wire)
    C



B
Go to step 11

C
Go to step 12
A

REPLACE CAN JUNCTION CONNECTOR CTR 

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER MAIN WIRE)


    C109571E21
  1. Disconnect the combination meter connector.



    C152894E85
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-6 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-17 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER MAIN WIRE)
OK

REPLACE COMBINATION METER (Click here)  

5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)
  1. Disconnect the CAN junction connector RH



  1. Measure the resistance according to the value(s) in the table below.


    C170177E04

    HINT:
    The resistance must be measured after the CAN junction connector CTR is disconnected.


    Standard resistance:

    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D59-1 (CANH) - D47-16 (BAT)
    R - LG
    ECM
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-12 (CANL) - D47-16 (BAT)
    W - LG
    ECM
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-5 (CANH) - D47-16 (BAT)
    SB - LG
    CAN junction connector CTR
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-16 (CANL) - D47-16 (BAT)
    W - LG
    CAN junction connector CTR
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (ECM main wire)
    B
    NG (CAN junction connector CTR main wire)
    C



B
Go to step 7

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR CTR - CAN JUNCTION CONNECTOR RH)
A


6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CAN JUNCTION CONNECTOR RH)


  1. Measure the resistance according to the value(s) in the table below.


    C170177E05


    Standard resistance:

    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D59-2 (CANH) - D47-16 (BAT)
    BR - LG
    Accessory gateway
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-13 (CANL) - D47-16 (BAT)
    W - LG
    Accessory gateway
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-3 (CANH) - D47-16 (BAT)
    LG - LG
    Air conditioning amplifier
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-14 (CANL) - D47-16 (BAT)
    W - LG
    Air conditioning amplifier
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-4 (CANH) - D47-16 (BAT)
    B - LG
    Skid control ECU
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-15 (CANL) - D47-16 (BAT)
    W - LG
    Skid control ECU
    Disconnect negative battery terminal
    6 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (Accessory gateway branch wire)
    B
    NG (Air conditioning amplifier branch wire)
    C
    NG (Skid control ECU branch wire)
    D



B
Go to step 15

C
Go to step 13

D
Go to step 14
A

REPLACE CAN JUNCTION CONNECTOR RH 

7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)


    C170023E02
  1. Disconnect the ECM connector.



    C152894E86
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D59-1 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-12 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM MAIN WIRE)
OK

REPLACE ECM (Click here)  

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)


    C165630E04
  1. Disconnect the yaw rate sensor connector.



    C152894E87
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-2 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-13 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR BRANCH WIRE)
OK

REPLACE YAW RATE SENSOR (Click here)  

9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)


    C131069E33
  1. Disconnect the center airbag sensor assembly connector.



    C152894E88
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-3 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-14 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)


    C165753E02
  1. Disconnect the steering angle sensor connector.



    C152894E89
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-5 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-16 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR BRANCH WIRE)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU BRANCH WIRE)


    C128052E10
  1. Disconnect the power steering ECU connector.



    C152894E91
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-7 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-18 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU BRANCH WIRE)
OK

REPLACE POWER STEERING ECU (Click here)  

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU BRANCH WIRE)


    C195604E02
  1. Disconnect the main body ECU connector.



    C152894E90
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D55-8 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D55-19 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU BRANCH WIRE)
OK

REPLACE MAIN BODY ECU 

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)


    C152868E03
  1. Disconnect the air conditioning amplifier connector.



    C152894E92
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D59-3 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-14 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)  

14.CHECK SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)


    C156384E48
  1. Disconnect the skid control ECU connector.



    C152894E93
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D59-4 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-15 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ACCESSORY GATEWAY BRANCH WIRE)
  1. Disconnect the accessory gateway connector.

    HINT:
    When accessories not connect it, repair or replace the accessory gateway branch wire or connector.



    C170244E37
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D59-2 (CANH) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher
    D59-13 (CANL) - D47-16 (BAT)
    Disconnect negative battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (ACCESSORY GATEWAY BRANCH WIRE)
OK

CHECK AND REPLACE THE ACCESSORY