Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TRAC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If TRAC control is turned off, the TRAC OFF indicator light will come on.

WIRING DIAGRAM


C170468E10


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (for 2GR-FE) (Click here)
OK


4.READ VALUE ON TECHSTREAM (VSC OFF SWITCH)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    VSC OFF switch / NORMAL, TRC OFF or VSC OFF
    NORMAL: Normal
    TRC OFF: TRAC off mode
    VSC OFF: VSC off mode
    -

  1. Using Techstream, check the switch condition on Techstream changes according to VSC OFF switch operation.

    OK:
    The Techstream display changes according to VSC OFF switch operation.



NG
Go to step 6
OK


5.INSPECT COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Perform the Active Test of the combination meter (meter CPU) using Techstream (Click here).

  1. Check the combination meter.

    OK:
    The TRAC OFF indicator light turns on or off in accordance with Techstream operation.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

6.INSPECT VSC OFF SWITCH


    C156489E01
  1. Turn the ignition switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (+) - 3 (E)
    Switch is pushed in
    Below 25 Ω
    6 (+) - 3 (E)
    Switch is not pushed in
    10 kΩ or higher



NG
REPLACE VSC OFF SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


    C160275E05
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-30 (CSW) - D43-6 (+)
    Always
    Below 1 Ω
    A24-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    D43-3 (E) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)