Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2195    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

DTC    P2196    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DTC    P2197    Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)

DTC    P2198    Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

The air fuel ratio sensor generates voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM (included in the hybrid vehicle control ECU) with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The air fuel ratio sensor is the planar type with an integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxides (NOx) into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the A/F sensor uses a current output element, the current is converted to a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A173183E01


DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
  1. Conditions (a) and (b) continue for 2 seconds or more
    (2 trip detection logic):
    1. (a) Air fuel ratio sensor voltage more than 3.8 V
    2. (b) Heated oxygen sensor voltage 0.21 V or more
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Intake system
  7. Fuel pressure
  8. Injector
  9. Hybrid vehicle control ECU
P2196
P2198
  1. Conditions (a) and (b) continue for 5 seconds or more
    (2 trip detection logic):
    1. (a) Air fuel ratio sensor voltage less than 2.8 V
    2. (b) Heated oxygen sensor voltage less than 0.59 V
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  4. A/F relay
  5. Air fuel ratio sensor heater and relay circuits
  6. Intake system
  7. Fuel pressure
  8. Injector
  9. Hybrid vehicle control ECU

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.
  5. When any of these DTCs are set, check the air fuel ratio sensor output voltage by entering the following menus on the Techstream: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1or AFS Voltage B2S1.
  6. Short-term fuel trim values can also be read using the Techstream.
  7. The ECM (included in the hybrid vehicle control ECU) regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the Techstream.
  8. If an air fuel ratio sensor malfunction is detected, the ECM sets a DTC.


MONITOR DESCRIPTION

  1. Sensor voltage detection monitor
    Under the air-fuel ratio feedback control, if the air fuel ratio sensor voltage output indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the air fuel ratio sensor. The ECM illuminates the MIL and sets a DTC.
    Example:
    If the air fuel ratio sensor voltage output is less than 2.8 V (very rich condition) and HO2 sensor output voltage falls from 0.59 V or higher to below 0.21 V for 5 seconds, the ECM sets DTC P2196 or P2198. Alternatively, if the air fuel ratio sensor voltage output is higher than 3.8 V (very lean condition) and HO2 sensor output voltage rises from below 0.21 V to 0.59 V or higher for 5 seconds, DTC P2195 or P2197 is set.
  1. Sensor current detection monitor
    A rich air-fuel mixture causes a low air fuel ratio sensor current, and a lean air-fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.
    If the air fuel ratio sensor output is 3.6 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and sets DTC P2195 or P2197 (high-side stuck). If the air fuel ratio sensor output is less than 0.78 mA for more than 3 seconds of cumulative time, the ECM sets DTC P2196 or P2198 (low-side stuck).

A107165E15


MONITOR STRATEGY


Related DTCs
P2195: air fuel ratio sensor (Bank 1) signal stuck lean
P2196: air fuel ratio sensor (Bank 1) signal stuck rich
P2197: air fuel ratio sensor (Bank 2) signal stuck lean
P2198: air fuel ratio sensor (Bank 2) signal stuck rich
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater - Sensor 1)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for Closed Loop)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0451, P0452, P0453, P1451, P1452, P1453 (EVAP system)
P0505 (Idle speed control)

Sensor voltage detection monitor (Lean side malfunction P2195, P2197): 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor voltage detection monitor (Rich side malfunction P2196, P2198): 
Time after engine start
30 seconds or more
Fuel system status
Closed-loop

Sensor current detection monitor P2195, P2196, P2197 and P2198 
Battery voltage
11 V or more
Atmospheric pressure
76 kPa (570 mmHg) or more
Air fuel ratio sensor status
Activated
Continuous time of fuel cut
3 to 10 seconds
Engine coolant temperature
75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Sensor voltage detection monitor (Lean side malfunction P2195, P2197): 
Rear heated oxygen sensor voltage
Rises from less than 0.21 V to 0.59 V or more
Air fuel ratio sensor voltage
More than 3.8 V

Sensor voltage detection monitor (Rich side malfunction P2196, P2198): 
Rear heated oxygen sensor voltage
Falls from 0.59 V or more to less than 0.21 V
Air fuel ratio sensor voltage
Less than 2.8 V

Sensor current detection monitor (High side malfunction P2195 and P2197): 
Air fuel ratio sensor current
3.6 mA or more

Sensor current detection monitor (Low side malfunction P2196 and P2198): 
Air fuel ratio sensor current
Less than 1.4 mA

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM


A179774E01


CONFIRMATION DRIVING PATTERN


A169890E09

  1. Connect the Techstream to the DLC3.
  2. Switch the ECM (included in the hybrid vehicle control ECU) from normal mode to check mode using the Techstream (Click here).
  3. Put the engine in inspection mode (Click here).
  4. Start the engine and warm it up with all the accessory switches OFF [A].
  5. Deactivate the inspection mode and drive the vehicle at 47 to 75 mph (75 to 120 km/h) for 5 to 10 minutes (the engine must be run during monitoring) [B].

    HINT:
    If any malfunction exists, the MIL will be illuminated during step (d).

    NOTICE:
    1. If the conditions in this test are not strictly followed, no malfunction will be detected. If you do not have the Techstream, turn the power switch off after performing steps 4 and 5, then perform steps 4 and 5 again.
    2. Do not drive the vehicle without deactivating inspection mode, otherwise damaging the transaxle may result.


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the Techstream.
  1. Connect the Techstream to the DLC3.
  2. Put the engine in inspection mode (Click here).
  3. Start the engine and turn the Techstream on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  6. Perform the Control the Injection Volume for A/F sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  7. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases in the fuel injection volume.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
+25%
Rich
Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio sensor)
-12.5%
Lean
More than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen sensor)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen senso)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensors (sensor 2) output has a maximum of 20 seconds of delay.


Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1
A162605E09
A162598E03
-
2
A162596E03
A162598E03
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E09
A162596E03
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A162596E03
A162596E03
  1. Fuel pressure
  2. Gas leakage from exhaust system
    (Air fuel ratio extremely lean or rich)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus on the Techstream: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2 and press the graph button on the Data List view.

HINT:
  1. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  2. A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, 2197 OR P2198)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) .

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197, or P2198
    A
    P2195, P2196, P2197, or P2198 and other DTCs
    B

    HINT:
    If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.

  1. On the Techstream, enter the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1 or AFS Voltage B2S1 and Engine Speed.



  1. Check the air fuel ratio sensor voltage three times, when the engine is in each of the following conditions:

    1. While idling (check for at least 30 seconds)

    2. Fully depress the accelerator pedal and run the engine at 2500 rpm.



    3. Accelerator pedal released.

      Standard voltage:

      Condition
      Air Fuel Ratio Sensor Voltage Variation
      Reference
      (1) and (2)
      Changes at approximately 3.3 V
      Between 3.1 V and 3.5 V
      (3)
      Increases to 3.8 V or more
      This occurs during engine deceleration
      (when fuel-cut performed)


      A182719E01

      HINT:
      1. For more information, see the diagrams below.
      2. If the output voltage of the air fuel ratio sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those above, the air fuel ratio sensor may have an open circuit. (This will also happen if the air fuel ratio sensor heater has an open circuit.)
      3. If the output voltage of the air fuel ratio sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those above, the air fuel ratio sensor may have a short circuit.
      4. The hybrid vehicle control ECU stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the air fuel ratio sensor output voltage.
      5. The hybrid vehicle control ECU must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 10 mph (16 km/h) to allow the hybrid vehicle control ECU to learn the closed throttle valve position.
      6. When the vehicle is driven:
        The output voltage of the air fuel ratio sensor may be below 2.8 V during fuel enrichment. The vehicle translates this as a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The air fuel ratio sensor is functioning normally.
      7. The air fuel ratio sensor is a current output element; therefore, the current is converted into a voltage inside the hybrid vehicle control ECU. Measuring the voltage at the connectors of the air fuel ratio sensor or hybrid vehicle control ECU will show a constant voltage result.



NG
Go to step 8
OK


3.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197 or P2198
    A
    Not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


5.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


6.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

    Result:

    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197 or P2198
    A
    Not output
    B



B
END
A

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

8.INSPECT AIR FUEL RATIO SENSOR


    A170689E02
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


9.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
  1. Inspect the A/F relay (Click here).



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK


10.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - HYBRID VEHICLE CONTROL ECU)


    A184181E04
  1. Disconnect the air fuel ratio sensor connectors.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B2-4 (HA1A)
    Always
    Below 1 Ω
    B20-3 (A1A+) - B2-22 (A1A+)
    Always
    Below 1 Ω
    B20-4 (A1A-) - B2-30 (A1A-)
    Always
    Below 1 Ω
    B19-1 (HA2A) - B2-3 (HA2A)
    Always
    Below 1 Ω
    B19-3 (A2A+) - B2-23 (A2A+)
    Always
    Below 1 Ω
    B19-4 (A2A-) - B2-31 (A2A-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B2-4 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B20-3 (A1A+) or B2-22 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B20-4 (A1A-) or B2-30 (A1A-) - Body ground
    Always
    10 kΩ or higher
    B19-1 (HA2A) or B2-3 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B19-3 (A2A+) or B2-23 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B19-4 (A2A-) or B2-31 (A2A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.



  1. Reconnect the air fuel ratio sensor connector.


    A133850E17



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks in from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


12.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


13.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check the injector injection (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read the DTCs using the Techstream.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A


17.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
CHECK FOR INTERMITTENT PROBLEMS (Click here)
YES

DTC CAUSED BY RUNNING OUT OF FUEL