Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light / red (malfunction) remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation has been disabled.

HINT:
The master caution indicator light will come on and a brake malfunction message will be displayed on the multi-information display if the EBD system is malfunctioning.


WIRING DIAGRAM


C175384E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK DTC
  1. Check if a ABS, VSC and/or electronically controlled brake system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


4.CHECK AUXILIARY BATTERY
  1. Check the auxiliary battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHARGE OR REPLACE AUXILIARY BATTERY
OK


5.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
C173879E01
  1. Disconnect the skid control ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A44-7 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


6.INSPECT SKID CONTROL ECU (GND TERMINAL)
  1. Turn the power switch off.


C173862E01

  1. Disconnect the skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A44-2 (GND2) - Body ground
    Always
    Below 1 Ω
    A44-1 (GND3) - Body ground
    Always
    Below 1 Ω
    A47-2 (GND4) - Body ground
    Always
    Below 1 Ω
    A47-1 (GND5) - Body ground
    Always
    Below 1 Ω
    A45-4 (GND6) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


7.READ VALUE USING TECHSTREAM (PARKING BRAKE SWITCH)
  1. Reconnect the skid control ECU connectors.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the Techstream, check the switch condition on the Techstream changes according to parking brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to parking brake pedal operation.



NG
Go to step 9
OK


8.INSPECT COMBINATION METER ASSEMBLY
  1. Turn the power switch off.

  1. Perform the Active Test of the combination meter (meter CPU) using the Techstream (Click here).

  1. Check the combination meter.

    HINT:
    Reinstall the connectors and restore the vehicle to its prior condition before checking the combination meter.

    OK:
    The brake warning light / red (malfunction) turns on or off in accordance with the Techstream operation.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE SKID CONTROL ECU (Click here)  

9.INSPECT PARKING BRAKE SWITCH


    C167308E01
  1. Turn the power switch off.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)
C175387E01
  1. Disconnect the main body ECU (instrument panel junction block) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-14 (PKB) - A17-1
    Always
    Below 1 Ω
    1C-14 (PKB) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)