Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > Skid Control Buzzer Circuit

for Preparation Click here


DESCRIPTION

The skid control buzzer sounds during VSC operation.

WIRING DIAGRAM


C174075E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.PERFORM ACTIVE TEST USING TECHSTREAM (SKID CONTROL BUZZER)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Active Test mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Buzzer
    Skid control buzzer
    Buzzer ON / OFF
    Buzzer can be heard

  1. Check that the buzzer sounds/stops when turning the skid control buzzer on/off using the Techstream.

    Result:

    Result
    Proceed to
    Buzzer does not sound or sounds constantly
    A
    Buzzer sounds/stops
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
END
A


2.INSPECT SKID CONTROL BUZZER (POWER SOURCE TERMINAL)


    C181786E03
  1. Turn the power switch off.

  1. Disconnect the skid control buzzer connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A16-2 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3.INSPECT SKID CONTROL BUZZER
C181788E01
  1. Turn the power switch off.

  1. Apply battery negative voltage to terminal 1, and battery positive voltage to terminal 2 of the skid control buzzer, and then check that the buzzer sounds.

    OK:
    The skid control buzzer sounds.



NG
REPLACE SKID CONTROL BUZZER (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL BUZZER)


    C193777E01
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A44-12 (BZ) - A16-1 (BZ)
    Always
    Below 1 Ω
    A44-12 (BZ) - Body ground
    Always
    10 kΩ or higher
    A44-33 (VBZ) - A16-2 (IG1)
    Always
    Below 1 Ω
    A44-33 (VBZ) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL)


  1. Disconnect the skid control ECU connectors.


    C173862E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A44-2 (GND2) - Body ground
    Always
    Below 1 Ω
    A44-1 (GND3) - Body ground
    Always
    Below 1 Ω
    A47-2 (GND4) - Body ground
    Always
    Below 1 Ω
    A47-1 (GND5) - Body ground
    Always
    Below 1 Ω
    A45-4 (GND6) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK

REPLACE SKID CONTROL ECU (Click here)