Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1241/41    Low Battery Positive Voltage

DTC    C1242/42    Open in IG1 / IG2 Power Source Circuit

for Preparation Click here


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU power source voltage drops, or there is insufficient voltage to operate either ABS main relay 1 or ABS main relay 2, the skid control ECU will store these codes.
These codes may be also be stored if the auxiliary battery voltage drops below 9.5 V.
If the power source voltage is too high, the skid control ECU will stop functioning and outputs no DTCs, and the ABS warning and brake warning / yellow (minor malfunction) lights remain on.

HINT:
DTC C1256/57 (accumulator low voltage malfunction) may also be memorized if there is a drop in power source voltage.


DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1241/41
81
System 1 is under the following conditions when the power switch is on (IG):
  1. Linear solenoid cannot receive enough current (brake is applied).
  2. BS1 voltage is less than 8.9 V for at least 3 seconds (brake is not applied).
  3. 12 V power source voltage inside ECU is less than 8.5 V when main relay is opened or VCM voltage is less than 4.7 V or 5 V or more for at least 0.05 seconds.
  1. Auxiliary battery
  2. ABS NO. 1 relay
  3. ABS NO. 1 relay circuit
  4. Brake control power supply (Capacitor)
  5. Hybrid control system (Charging circuit)
  6. Skid control ECU
↑
82
System 2 is under the following conditions when the power switch is on (IG):
  1. Linear solenoid cannot receive enough current (brake is applied).
  2. BS2 voltage is less than 8.9 V for at least 3 seconds (brake is not applied).
  3. 12 V power source voltage inside ECU is less than 8.5 V when main relay is opened or VCM voltage is less than 4.7 V or 5.3 V or more for at least 0.05 seconds.
  1. Auxiliary battery
  2. ABS NO. 2 relay
  3. ABS NO. 2 relay circuit
  4. Brake control power supply (Capacitor)
  5. Hybrid control system (Charging circuit)
  6. Skid control ECU
↑
83
Capacitor mode signal is received from brake control power supply for 3 seconds or more when the power switch is on (IG).
  1. Auxiliary battery
  2. Brake control power supply (Capacitor)
  3. Hybrid control system (Charging circuit)
↑
84
ABS is requested to operate when the power source voltage of the main relay system is dropping.
  1. ABS NO. 1 relay
  2. ABS NO. 1 relay circuit
  3. ABS NO. 2 relay
  4. ABS NO. 2 relay circuit
  5. Brake control power supply (Capacitor)
  6. Hybrid control system (Charging circuit)
  7. Skid control ECU
C1242/42
87
The power supply voltage is not applied to the IG1 terminal, power supply voltage is applied to the IG2 terminal, and +BI1 terminal voltage is 9.5 V or more for 4 seconds or more.
  1. Auxiliary battery
  2. IG1 power source circuit
  3. Hybrid control system (Charging circuit)
  4. Skid control ECU
↑
88
The power supply voltage is applied to the IG1 terminal, power supply voltage is not applied to the IG2 terminal, and +BI1 terminal voltage is 9.5 V or more for 4 seconds or more.
  1. Auxiliary battery
  2. IG2 power source circuit
  3. Hybrid control system (Charging circuit)
  4. Skid control ECU

WIRING DIAGRAM


C135844E02


C173859E01


C173860E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK HYBRID CONTROL SYSTEM
  1. Check if the hybrid control system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT HYBRID CONTROL SYSTEM (Click here)
A


2.CHECK AUXILIARY BATTERY
  1. Check the auxiliary battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHARGE OR REPLACE AUXILIARY BATTERY
OK


3.INSPECT SKID CONTROL ECU (IG AND +BI TERMINAL)
C173861E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A44-7 (IG1) - Body ground
    Power switch on (IG)
    11 to 14 V
    A45-5 (IG2) - Body ground
    Power switch on (IG)
    11 to 14 V
    A44-3 (+BI1) - Body ground
    Always
    11 to 14 V
    A47-5 (+BI2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG OR +BI CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (GND TERMINAL)
  1. Turn the power switch off.


C173862E01

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A44-2 (GND2) - Body ground
    Always
    Below 1 Ω
    A44-1 (GND3) - Body ground
    Always
    Below 1 Ω
    A47-2 (GND4) - Body ground
    Always
    Below 1 Ω
    A47-1 (GND5) - Body ground
    Always
    Below 1 Ω
    A45-4 (GND6) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (RELAY TERMINAL)


    C173833E02
  1. Reconnect the skid control ECU connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A46-2 (R1+) - Body ground
    Power switch on (IG)
    9.1 to 13.6 V
    A45-17 (R2+) - Body ground
    Power switch on (IG)
    9.1 to 13.6 V
    A46-12 (SR1) - Body ground
    Power switch on (IG)
    Below 1 V
    A45-15 (SR2) - Body ground
    Power switch on (IG)
    Below 1 V
    A46-3 (BS1) - Body ground
    Power switch on (IG)
    8.8 to 14 V
    A45-7 (BS2) - Body ground
    Power switch on (IG)
    8.8 to 14 V


    Result:

    Result
    Proceed to
    OK
    A
    NG (R1+ and/or R2+ voltage is not within the specified range)
    B
    NG (SR1, SR2, BS1 and/or BS2 voltage is not within the specified range)
    C



B
REPLACE SKID CONTROL ECU (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (RELAY CIRCUIT)
A


6.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1241/41 and C1242/42) are not output
    A
    DTCs (C1241/41 and/or C1242/42) are output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)