Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1311/11    Open in Main Relay 1 Circuit

DTC    C1312/12    Short in Main Relay 1 Circuit

DTC    C1313/13    Open in Main Relay 2 Circuit

DTC    C1314/14    Short in Main Relay 2 Circuit

for Preparation Click here


DESCRIPTION

The ABS main relay 1 supplies power to the changeover solenoid and the linear solenoid.
The ABS main relay remains on for approximately 2 minutes after the power switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1311/11
1
Either of the following is detected:
  1. Relay contact is off (BS1 terminal is less than 3.5 V) for at least 0.2 seconds when R1+ terminal voltage is 9.5 V or more and ABS main relay 1 is on.
  2. R1+ terminal voltage is less than 9.5 V and ABS main relay 1 cannot be on for at least 0.2 seconds when ABS main relay 1 is turned on (BS1 terminal is 3.5 V or more).
  1. ABS NO. 1 relay
  2. ABS NO. 1 relay circuit
  3. Skid control ECU
C1312/12
3
Relay contact is on for at least 4 seconds when ABS main relay 1 is off.
↑
C1313/13
4
Either of the following is detected:
  1. Relay contact is off (BS2 terminal is less than 3.5 V) for at least 0.2 seconds when R2+ terminal voltage is 9.5 V or more and ABS main relay 2 is on.
  2. R2+ terminal voltage is less than 9.5 V and ABS main relay 2 cannot be on for at least 2 seconds when ABS main relay 2 is turned on (BS2 terminal is 3.5 V or more).
  1. ABS NO. 2 relay
  2. ABS NO. 2 relay circuit
  3. Skid control ECU
C1314/14
6
Relay contact is on for at least 4 seconds when ABS main relay 2 is off.
↑

WIRING DIAGRAM

Refer to DTCs C1241/41 and C1242/42 .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MAIN RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Active Test mode on the Techstream (Click here).

    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ECB* Main Relay
    ABS main relay
    Relay ON / OFF
    Operating sound of relay
    (clicking sound) can be heard
    ECB* Main Relay2
    ABS main relay 2
    Relay ON / OFF
    Operating sound of relay
    (clicking sound) can be heard
    *: Electronically Controlled Brake System

  1. Check the operating sound of the ABS main relay when operating it with the Techstream.

    OK:
    The operating sound of the ABS main relay should be heard.



NG
Go to step 4
OK


2.INSPECT SKID CONTROL ECU (BS TERMINAL)


    C173833E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A46-3 (BS1) - Body ground
    Power switch on (IG)
    8.8 to 14 V
    A45-7 (BS2) - Body ground
    Power switch on (IG)
    8.8 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)
OK


3.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1311/11, C1312/12, C1313/13 and C1314/14) are not output
    A
    DTCs (C1311/11, C1312/12, C1313/13 and/or C1314/14) are output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.INSPECT ABS FUSES
C173888E01
  1. Turn the power switch off.

  1. Remove the ABS NO. 1, ABS NO. 2 and ABS NO. 3 fuses from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ABS NO. 1 (10 A) fuse
    Always
    Below 1 Ω
    ABS NO. 2 (10 A) fuse
    Always
    Below 1 Ω
    ABS NO. 3 (15 A) fuse
    Always
    Below 1 Ω



NG
REPLACE ABS FUSES
OK


5.INSPECT ABS MAIN RELAY (ABS NO. 1, 2)
C143433E05
  1. Install the ABS NO. 1, ABS NO. 2 and ABS NO. 3 fuses.

  1. Remove the ABS NO. 1 relay and ABS NO. 2 relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE ABS MAIN RELAY (ABS NO. 1, 2)
OK


6.INSPECT SKID CONTROL ECU (+BI TERMINAL)


    C173889E01
  1. Install the ABS NO. 1 relay and ABS NO. 2 relay.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A44-3 (+BI1) - Body ground
    Always
    11 to 14 V
    A47-5 (+BI2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BI CIRCUIT)
OK


7.INSPECT SKID CONTROL ECU (RELAY TERMINAL)


    C173833E06
  1. Reconnect the skid control ECU connectors.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A46-2 (R1+) - Body ground
    Power switch on (IG)
    9.1 to 13.6 V
    A45-17 (R2+) - Body ground
    Power switch on (IG)
    9.1 to 13.6 V
    A44-5 (+BO1) - Body ground
    Power switch on (IG)
    8.8 to 14 V
    A47-4 (+BO2) - Body ground
    Power switch on (IG)
    8.8 to 14 V



NG
REPLACE SKID CONTROL ECU (Click here)
OK


8.INSPECT SKID CONTROL ECU (BS TERMINAL)


    C173833E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A46-3 (BS1) - Body ground
    Power switch on (IG)
    8.8 to 14 V
    A45-7 (BS2) - Body ground
    Power switch on (IG)
    8.8 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)
OK

REPLACE SKID CONTROL ECU (Click here)