Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1319/35    SCSS Changeover Solenoid Malfunction

for Preparation Click here


DESCRIPTION

The stroke simulator solenoid (SCSS) generates pedal reactive effort during electronically controlled brake system control. If one or both of the front wheels loses brake accumulator function, the simulator operation is prohibited.

DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1319/35
71
Either of the following is detected:
  1. SCSS drive circuit is malfunctioning for 0.05 seconds or more.
  2. Short to +B in SCSS.
  1. Brake stroke simulator
  2. Brake stroke simulator circuit
  3. Skid control ECU
↑
72
Current leaks for 0.05 seconds or more when SCSS is off.
↑
↑
73
Open circuit in SCSS continues for 0.05 seconds or more.
↑
↑
74
Overcurrent in SCSS continues for 0.05 seconds or more.
↑

WIRING DIAGRAM


C173894E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

1.INSPECT BRAKE STROKE SIMULATOR CYLINDER
C173926E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the brake stroke simulator cylinder connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (BSR) - 2 (SCSS)
    Always
    21.45 to 23.15 Ω
    1 (BSR) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE BRAKE STROKE SIMULATOR CYLINDER (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE STROKE SIMULATOR CYLINDER)
C173925E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A46-13 (SCSS) - A51-2 (SCSS)
    Always
    Below 1 Ω
    A46-13 (SCSS) - Body ground
    Always
    10 kΩ or higher
    A46-3 (BS1) - A51-1 (BSR)
    Always
    Below 1 Ω
    A46-3 (BS1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SKID CONTROL ECU (SOLENOID INPUT)


    C173833E08
  1. Reconnect the skid control ECU connector and the brake stroke simulator cylinder connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A46-13 (SCSS) - Body ground
    Brake pedal depressed (Brake stroke simulator ON)
    Below 1.5 V
    A46-13 (SCSS) - Body ground
    Brake pedal released (Brake stroke simulator OFF)
    11 to 14 V



NG
REPLACE SKID CONTROL ECU (Click here)
OK


4.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTC (C1319/35) is not output
    A
    DTC (C1319/35) is output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)