Home › ENGINE › 3MZ-FE ENGINE MECHANICAL › ENGINE

ENGINE > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT COOLANT

HINT:
Click here.



2. INSPECT ENGINE OIL

HINT:
Click here.



3. INSPECT BATTERY

Standard specific gravity:
1.25 to 1.29 at 20°C (68°F)



4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element from the air cleaner case.

  1. Visually check that there is no dirt, clog, and damage to the air cleaner filter element.

    HINT:
    1. If there is any dirt or a clog on the air cleaner filter element, clean it with compressed air.
    2. If any dirt or a clog remains even after cleaning the air cleaner filter element with compressed air, replace it.



5. INSPECT SPARK PLUG

NOTICE:
  1. Never use a wire brush for cleaning.
  2. Never attempt to adjust the electrode gap on a used spark plug.



    I039522E10
  1. Check the electrode.

    1. Using a megohmmeter, measure the insulation resistance.

      Standard insulation resistance:
      10 MΩ or higher

      HINT:
      1. If the result is below 10 MΩ, clean the plug and measure the resistance again.
      2. If a megohmmeter is not available, perform the following inspection instead.

  1. Alternative inspection method:

    1. Quickly accelerate the engine to 4000 rpm 5 times.

    2. Remove the spark plugs.

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator. If there is damage, replace the spark plug.

    Recommended spark plug:
    Manufacturer
    Spark Plug Type
    DENSO
    SK20R11
    NGK
    IFR6A11

    NOTICE:
    Use only the listed spark plug or equivalent to ensure engine performance and smooth driveability.



    A182917E01
  1. Check the spark plug electrode gap.

    Maximum electrode gap for a used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for a new spark plug (for reference):
    1.0 to 1.1 mm (0.039 to 0.043 in.)



    B062019
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard air pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

  1. Install the ignition coil assembly and spark plug (Click here).



6. INSPECT IGNITION TIMING
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter DATA LIST MODE on the Techstream.

      Ignition timing:
      8 to 12° BTDC

      NOTICE:
      1. Turn all the electrical systems off.
      2. Inspect the engine idle speed with the cooling fan off.

      HINT:
      Refer to the Techstream operator's manual if you need help to select DATA LIST.

    3. Check that the ignition timing advances immediately when the engine speed is increased.



  1. When not using the Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting wrong terminals can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor is turned off.



    2. A108139
    3. Pull out the red-colored wire harness as shown in the illustration.

    4. Connect the tester terminal of the timing light to the red-colored wire.

      NOTICE:
      Use a timing light which detects the first signal.

    5. Inspect ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC

      NOTICE:
      When checking the ignition timing, the transmission is in neutral.

      HINT:
      Run the engine at 1,000 to 1,300 rpm for 5 seconds, check that the engine rpm returns to idle speed.

    6. Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.

    7. Inspect ignition timing at idle.

      Ignition timing:
      7 to 24° BTDC

    8. Confirm that the ignition timing advances when the engine rpm is increased.

    9. Remove the timing light.



7. INSPECT ENGINE IDLE SPEED
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine.

  1. Connect the Techstream to the DLC3.

  1. Enter DATA LIST MODE on the Techstream.

    Idle speed:
    850 to 950 rpm.

    NOTICE:
    1. When checking the idle speed, the transmission is in neutral.
    2. Check the idle speed with the cooling fan off.
    3. Switch off all accessories and air conditioning before connecting the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.



8. INSPECT COMPRESSION
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up and stop the engine.

  1. Remove the intake air surge tank (Click here).

    NOTICE:
    If the throttle body connector is disconnected because the DTC is detected in inspection, always reconnect it.

  1. Disconnect the injector connectors.

  1. Remove the ignition coils.

    NOTICE:
    If the ignition coil assembly connector is disconnected because the DTC is detected in inspection, always reconnect it.

  1. Remove the spark plugs.



  1. Inspect cylinder compression pressure.



      P019471E01
    1. Insert a compression gauge into the spark plug hole.

    2. Connect the Techstream to the DLC3.

      NOTICE:
      Check the fully charged battery to indicate HV battery voltage in the ECU data list.

    3. Enter ACTIVE TEST MODE on the Techstream.

    4. While cranking the engine, measure the compression pressure.

      Compression pressure:
      0.98 MPa (10 kgf/cm2, 142 psi)

      Minimum pressure:
      0.74 MPa (7.5 kgf/cm2, 107 psi)

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi)

      NOTICE:
      1. Check other cylinder's compression pressure in the same way.
      2. This measurement must be done as quickly as possible.
      3. After performing all the procedures, be sure to clear DTCs stored in the the memory. Then, check that the normal system code is output.

    5. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.



9. INSPECT CO/HC
  1. Set the vehicle to inspection mode (Click here).

  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.



    A175874
  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idling.

  1. Check CO/HC concentration at idle and/or 2,500 rpm.

    HINT:
    When doing the 2 mode (idle and 2,500 rpm) test, the measuring procedures are prescribed by the applicable local regulations.

    If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check heated oxygen sensor operation (Click here).

    2. Check heated air fuel ratio sensor operation (Click here).

    3. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Defective water temperature sensor
        3. Defective mass air-flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor