Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P2601-779    Coolant Pump Control Circuit Range / Performance

for Preparation Click here


DESCRIPTION

HINT:
Although the DTC title refers to "coolant pump", this DTC is related to the oil pump control circuit.

Refer to the description for DTC P2601-777 .

DTC No.
INF No.
DTC Detection Condition
Trouble Area
P2601
779
  1. Abnormal power source voltage is detected by oil pump with motor assembly
  2. Power source voltage input to oil pump with motor assembly is 6.96 V or less for 2 seconds or more with OIL PMP relay on
  1. Wire harness or connector
  2. Oil pump with motor assembly
  3. OIL PMP fuse
  4. Hybrid vehicle control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC P2601-777 .

INSPECTION PROCEDURE

NOTICE:
  1. When troubleshooting the oil pump with motor assembly, check for the following conditions:
    1. ATF temperature inside the oil cooler is 41°F (5°C) or more.
    2. The ambient temperature sensor value is 41°F (5°C) or more.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P0A08-264 is not output.
    A
    DTC P0A08-264 is output.
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK FUSE (OIL PMP)


    A175454E02
  1. Remove the OIL PMP fuse from the engine room relay block .

  1. Check for continuity of the OIL PMP fuse.

    OK:
    There is continuity.



NG
REPLACE FUSE (OIL PMP)
OK


3.CLEAR DTC (HV)
  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


4.CHECK DTC OUTPUT (HV)
  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P0A08-264 is output again.
    A
    DTC P0A08-264 is not output.
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - OIL PMP - BODY GROUND)
  1. Turn the power switch off.

  1. Disconnect the cable from the positive auxiliary battery terminal.

  1. Remove the OIL PMP relay from the No. 3 engine room relay block.

  1. Disconnect the oil pump with motor assembly connector.



    A175444E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance
    Positive auxiliary battery terminal - OIL PMP relay terminal 5
    Power switch off
    Below 2 Ω
    R1
    OIL PMP relay terminal 3 - A48-4 (L)
    Power switch off
    Below 2 Ω
    R2
    A48-1 (OPG) - Body ground
    Power switch off
    Below 2 Ω
    R3

    Standard:
    Combined resistance (R1, R2 and R3) of each part in the wire harness is below 6 Ω.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HYBRID VEHICLE CONTROL ECU
  1. Connect the oil pump with motor assembly connector.

  1. Connect the OIL PMP relay to the No. 3 engine room relay block.

  1. Connect the cable to the positive auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Inspection Mode - 2WD Inspection.

  1. Turn the power switch on (READY).



    A175144E02
  1. Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.
    Item
    Condition
    Terminal
    A43-7 (OPST) - B3-5 (E1)
    Equipment Setting
    5 V/DIV., 5 ms./DIV.
    Condition
    Power switch on (READY)

    OK:
    The waveform appears as shown in the illustration.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPLACE OIL PUMP WITH MOTOR ASSEMBLY (Click here)