Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A08-264    DC / DC Converter Status Circuit

for Preparation Click here


DESCRIPTION

Refer to the description of the DC/DC converter .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A08
264
DC/DC converter malfunction
  1. Wire harness or connector
  2. Water pump with motor and bracket assembly
  3. Inverter cooling system
  4. Hybrid vehicle transaxle assembly
  5. No. 3 frame wire
  6. Rear traction motor with transaxle assembly
  7. Inverter with converter assembly
  8. INV-W/P fuse
  9. DC/DC-S fuse
  10. Fusible link
  11. Cooling fan system

WIRING DIAGRAM


A175702E02


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be OV before begining work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A08-264 only is output.
    A
    Any of the following DTCs are also output.
    B

    DTC No.
    Relevant Diagnosis
    P0A05-776
    Motor Electronics Coolant Pump Control Circuit / Open
    P0A93-346, 347
    Inverter Cooling System Performance
    P0A94-547, 548, 549
    DC / DC Converter Performance
    P0AA6-526, 613, 655
    Hybrid Battery Voltage System Isolation Fault
    P0ADB-227
    Hybrid Battery Positive Contactor Control Circuit Low
    P0ADF-229
    Hybrid Battery Negative Contactor Control Circuit Low
    P3004-131, 803
    Power Cable Malfunction



B
GO TO DTC CHART (Click here)
A


2.CHECK RELAY BLOCK ASSEMBLY


    A174897E01
  1. Check the condition of the fusible links (ALT and MAIN) and fuse (DC/DC-S) in the relay block. Check if the circuits are open.

    OK:
    They are connected securely. There are no open circuits in the fuse or fusible links.



NG
REPLACE FUSIBLE LINK OR FUSE, OR REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)


    A174883E01
  1. Check the connections of the hybrid vehicle control ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


4.CHECK CONNECTOR CONNECTION CONDITION (MG ECU CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.



    A170989E01
  1. Check the connections of the MG ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


5.CHECK INSULATION RESISTANCE OF HIGH-VOLTAGE SYSTEM

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.



    A174238E03
  1. Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

    NOTICE:
    Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    MG2 U - Body ground and shield ground
    Power switch off
    1 MΩ or higher
    MG2 V - Body ground and shield ground
    Power switch off
    1 MΩ or higher
    MG2 W - Body ground and shield ground
    Power switch off
    1 MΩ or higher

    HINT:
    Perform this inspection while the three-phase AC cable for MG2 is connected.



NG
Go to step 16
OK


6.CHECK CONNECTION CONDITION (AMD TERMINAL)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.



    A174239E05
    A175614E03
  1. Remove the three-phase AC cable for MGR from the inverter with converter assembly.

  1. Check the connection of the AMD terminal.

    OK:
    The terminal is connected securely and there are no contact problems.



NG
Go to step 18
OK


7.CHECK TERMINAL VOLTAGE (AMD TERMINAL)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Check that the service plug grip is not installed.



    A174887E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AMD terminal (Inverter with converter assembly side) - Body ground
    Power switch off
    11 to 14 V



NG
Go to step 19
OK


8.CHECK INVERTER WITH CONVERTER ASSEMBLY (MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

  1. Turn the power switch on (IG).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    HINT:
    Turning the power switch on (IG) with the service grip and inverter cover removed causes interlock switch system DTC P0A0D-350 to be output.



    A174223E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A42-7 (+B) - Body ground
    Power switch on (IG)
    11 to 14 V
    A42-4 (+B2) - Body ground
    Power switch on (IG)
    11 to 14 V
    A42-35 (SI) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE HYBRID VEHICLE CONTROL ECU)
  1. Turn the power switch off.

  1. Disconnect the A42 connector from the MG ECU.



    A174426E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A42-33 (NODD) - Body ground
    Power switch off
    120 to 140 kΩ



NG
Go to step 20
OK


10.INSPECT INVERTER WITH CONVERTER ASSEMBLY (OPERATION OF DC/DC CONVERTER)

HINT:
The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flowing from the auxiliary battery instead.



    A174427E02
  1. Connect the AC/DC 400 A probe to the positive auxiliary battery line.

  1. Install the inverter cover (Click here).

  1. Install the service plug grip.

  1. Turn the power switch on (READY) and leave the vehicle as it is until the electric current flowing into the auxiliary battery becomes 10 A or less.



    A174428E02
  1. Measure the current flowing from the auxiliary battery with the headlight position switch and blower motor switch in the HI position, and the rear window defogger turned on.

  1. Measure the auxiliary battery voltage according to the previous conditions with the lights, blower motor and rear window defogger turned on.

    Result:

    Item
    Condition
    Specified Condition
    Current flowing from auxiliary battery
    The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.
    0 A or less (no current from auxiliary battery)
    Auxiliary battery voltage
    The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.
    13 to 15 V



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK


11.CHECK QUANTITY OF HV COOLANT


    A169560E01
  1. Check the coolant level in the inverter reserve tank.

  1. Check for coolant leaks.

    Result:
    Result
    Proceed to
    Coolant leaks are not evident. A sufficient amount of coolant remains in the inverter reserve tank.
    A
    Coolant leaks are not evident. No coolant remains in the inverter reserve tank.
    B
    Coolant leaks are evident
    C

    HINT:
    After repairing the coolant leaks and adding coolant, perform the "Activate the Water Pump" active test (HV ECU active test item) and the "Control the Electric Cooling Fan" active test (ENHANCED OBDII active test item) and make sure that there are no malfunctions.



B
ADD HV COOLANT

C
CHECK FOR COOLANT LEAKS AND ADD COOLANT
A


12.CHECK COOLANT HOSE


    A105138E03
  1. Check if the hoses of the cooling system are kinked or clogged.

    OK:
    The hoses of the cooling system are not kinked or clogged.



NG
CORRECT THE PROBLEM
OK


13.CHECK CONNECTOR CONNECTION CONDITION (WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY CONNECTOR)


    A174885
  1. Check the connection of the water pump with motor and bracket assembly connector.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


14.PERFORM ACTIVE TEST USING TECHSTREAM (WATER PUMP)
  1. Turn the the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

  1. Perform the "Activate the Water Pump" active test for at least 1 minute.



    A169560E01
  1. Check that there are ripples in the coolant in the inverter reserve tank.

    OK:
    There are ripples in the coolant in the inverter reserve tank as long as the active test is being performed.

    NOTICE:
    In addition to the active test, the water pump with motor and bracket assembly will also operate with the power switch on (READY). However, the water pump with motor and bracket assembly will not operate for 20 seconds after the power switch is turned on (READY).

    HINT:
    The water pump with motor and bracket assembly will also operate in inspection mode.



NG
Go to step 22
OK


15.PERFORM ACTIVE TEST USING TECHSTREAM (COOLING FAN)
  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

  1. Perform the "Control the Electric Cooling Fan" active test.

    OK:
    The cooling fan rotates.



NG
CHECK COOLING FAN SYSTEM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

16.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2 AND MG1)

CAUTION:
Be sure to wear insulated gloves.



  1. Check that the service plug grip is not installed.


    A174429E03

  1. Disconnect the three-phase AC cables for the hybrid vehicle transaxle assembly (MG2 and MG1) from the inverter with converter assembly.



    A174430E04
  1. Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

    NOTICE:
    Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    MG2 U terminal - Body ground and shield ground
    Power switch off
    100 MΩ or higher
    MG2 V terminal - Body ground and shield ground
    Power switch off
    100 MΩ or higher
    MG2 W terminal - Body ground and shield ground
    Power switch off
    100 MΩ or higher
    MG1 U terminal - Body ground and shield ground
    Power switch off
    100 MΩ or higher
    MG1 V terminal - Body ground and shield ground
    Power switch off
    100 MΩ or higher
    MG1 W terminal - Body ground and shield ground
    Power switch off
    100 MΩ or higher



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


17.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.



    A174239E07
  1. Check that the service plug grip is not installed.

  1. Disconnect the three-phase AC cable for MGR from the inverter with converter assembly.



    A108040E07
  1. Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

    NOTICE:
    Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    MGR U terminal - Body ground and shield ground
    Power switch off
    10 MΩ or higher
    MGR V terminal - Body ground and shield ground
    Power switch off
    10 MΩ or higher
    MGR W terminal - Body ground and shield ground
    Power switch off
    10 MΩ or higher



NG
Go to step 21
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

18.CHECK AMD TERMINAL

CAUTION:
Be sure to wear insulated gloves.



    A175614E02
  1. Check for arc marks on the AMD terminals (inverter with converter assembly side and wire harness side).

    OK:
    There are no arc marks.

    HINT:
    The wire harness between the AMD terminal on the inverter with converter assembly side and the AMD terminal on the vehicle side is supplied with the inverter with converter assembly as a unit. If the wire harness is faulty, replace the inverter with converter assembly.



NG
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
OK

CONNECT SECURELY 

19.CHECK TERMINAL VOLTAGE (AMD TERMINAL)


    A174887E01
  1. Turn the power switch off.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AMD terminal - Body ground
    Power switch off
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

20.INSPECT HYBRID VEHICLE CONTROL ECU


    A174431E04
  1. Disconnect all hybrid vehicle control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-11 (NODD) - B3-5 (E1)
    Power switch off
    120 to 140 kΩ



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

21.INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.



    C105715
  1. Disconnect the No. 3 frame wire (three-phase AC cable for MGR) from the rear traction motor with transaxle assembly.



    A174905E08
  1. Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

    NOTICE:
    Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    MGR U terminal - Body ground and shield ground
    Power switch off
    10 MΩ or higher
    MGR V terminal - Body ground and shield ground
    Power switch off
    10 MΩ or higher
    MGR W terminal - Body ground and shield ground
    Power switch off
    10 MΩ or higher

    NOTICE:
    Wrap terminals U, V, and W of the No. 3 frame wire (three-phase AC cable for MGR) on the inverter with converter assembly side with insulating tape to prevent the terminals from shorting to ground.



NG
REPLACE NO. 3 FRAME WIRE
OK

REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (Click here)  

22.CHECK FUSE (INV-W/P)


    A174902E03
  1. Check if there is an open circuit in the fuse (INV-W/P) in the No. 2 engine room relay block.

    OK:
    There is no open circuit in the fuse (INV-W/P).

    HINT:
    If the result is NG, replace the fuse (INV-W/P) with a new one.



NG
REPLACE FUSE (INV-W/P)
OK


23.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - WATER PUMP)


    A184421E04
  1. Turn the power switch off.

  1. Disconnect the D35 connector from the hybrid vehicle control ECU.

  1. Disconnect the A52 water pump with motor and bracket assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-29 (NIWP) - A52-1 (NWP)
    Power switch off
    Below 1 Ω
    D35-23 (IWP) - A52-2 (SWP)
    Power switch off
    Below 1 Ω
    A52-3 (GND) - Body ground
    Power switch off
    Below 1 Ω
    INV-W/P fuse terminal 2 - A52-4 (+BWP)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    D35-29 (NIWP) or A52-1 (NWP) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    D35-23 (IWP) or A52-2 (SWP) - Body ground and other terminals
    Power switch off
    10 kΩ or higher
    INV-W/P fuse terminal 2 or - A52-4 (+BWP) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

INSPECT WATER PUMP WITH MOTOR AND BRACKET ASSEMBLY CIRCUIT