Home › STEERING › POWER STEERING › STEERING GEAR

STEERING GEAR > INSTALLATION

for Preparation Click here



1. INSTALL TIE ROD ASSEMBLY LH


    C165553E01
  1. Install the lock nut and the tie rod assembly LH to the steering rack end sub-assembly until the matchmarks are aligned.

    HINT:
    After adjusting toe-in, torque the lock nut.



2. INSTALL TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



3. INSTALL POWER STEERING LINK ASSEMBLY


    C174974
  1. Install the power steering link assembly with the 2 bolts and 2 nuts.

    Torque:
    70 N*m{ 713 kgf*cm , 51 ft.*lbf }

    NOTICE:
    1. Make sure to tighten the bolts starting from the left side of the vehicle.
    2. Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



4. INSTALL FRONT STABILIZER BAR
  1. Install the front stabilizer bar by inserting it from the right side of the vehicle.



5. INSTALL FRONT NO. 1 STABILIZER BRACKET LH


    C167140
  1. Install the No. 1 front stabilizer bracket LH to the front frame assembly with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



6. INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



7. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


    A080812E02
  1. Set the engine assembly with transaxle on the engine lifter.

  1. Install the engine assembly to the vehicle.

  1. Install the frame side plates RH and LH with the 6 bolts and 2 nuts.

    Torque:
    Bolt A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }
    Nut C:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



    A080813E02
  1. Install the front suspension member brace RH and LH with the 6 bolts and 2 nuts.

    Torque:
    Bolt A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    Bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }
    Nut C:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



8. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C165545E01
  1. Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.



    C165544
  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



9. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    C165537E05
  1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.



10. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



11. INSTALL FRONT NO. 1 SUSPENSION ARM SUB-ASSEMBLY LOWER LH


    C165929
  1. Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }



12. INSTALL FRONT NO. 1 SUSPENSION ARM SUB-ASSEMBLY LOWER RH

HINT:
Perform the same procedure as for the LH side.



13. CONNECT TIE ROD ASSEMBLY LH
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



14. CONNECT TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



15. INSTALL FRONT SPEED SENSOR LH


    C165818E03
  1. Install the resin clamp and front speed sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from attaching to the sensor tip.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.



16. INSTALL FRONT SPEED SENSOR RH

HINT:
Perform the same procedure as for the LH side.



17. INSTALL FRONT AXLE SHAFT NUT LH
  1. Clean the threaded parts on the drive shaft and front axle shaft nut LH using a non-residue solvent.

    HINT:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C165538
  1. Using a socket wrench (30 mm), install a new front axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle shaft nut.



18. INSTALL FRONT AXLE SHAFT NUT RH

HINT:
Perform the same procedure as for the LH side.



19. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C165915
  1. Install the front stabilizer link assembly to the front shock absorber with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



20. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



21. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY


    A077857
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length:
    41.5 mm (1.634 in.)

    HINT:
    If the free length is less than the minimum, replace the compression spring.



    A078440E01
  1. Install a new gasket to the front No. 3 exhaust pipe as shown in the illustration.



    A109431
  1. Install 2 new gaskets and the front No. 3 exhaust pipe with the 2 bolts and 2 new nuts.

    Torque:
    Bolt:
    48 N*m{ 490 kgf*cm , 35 ft.*lbf }
    Nut:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. Connect the heated oxygen sensor connector.



22. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A109430
  1. Install 2 new gaskets and the front No. 3 exhaust pipe with the 2 bolts and 2 new nuts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. Connect the heated oxygen sensor connector.



23. CONNECT ENGINE WIRE


    A175953
  1. Connect the connector and clamp.



    A175954
  1. Install the ground cable and clamp.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



    A175955
  1. Install the clamp and wire harness protector.



    A175941
  1. Install the 2 nuts and pull in the engine wire harness.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the 6 connectors to the ECM.



    A175952
  1. Connect the 2 connectors.



24. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.



    B168370
  1. Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <E>.



25. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B173000
  1. Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.



26. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



27. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



28. CONNECT WATER HOSE


    A175956
  1. Using pliers, grip the claws of the clip and slide the clip to connect the water inlet hose.



    A175957
  1. Using pliers, grip the claws of the clip and slide the clip to connect the water inlet hose.



29. CONNECT INLET OIL COOLER TUBE SUB-ASSEMBLY


    A112533
  1. Using pliers, grip the claws of the clip and slide the clip to connect the inlet oil cooler tube.



30. CONNECT OUTLET OIL COOLER TUBE SUB-ASSEMBLY

HINT:
Connect the outlet oil cooler tube using the same procedure as for the inlet oil cooler tube.



31. CONNECT INLET RADIATOR HOSE


    A175876
  1. Using pliers, grip the claws of the clip and slide the clip to connect the inlet radiator hose.



32. CONNECT OUTLET RADIATOR HOSE


    A175942
  1. Using pliers, grip the claws of the clip and slide the clip to connect the outlet radiator hose.



33. CONNECT INLET HEATER WATER HOSE


    A108717E03
  1. Using pliers, grip the claws of the clip and slide the clip to connect the inlet heater water hose.



34. CONNECT OUTLET HEATER WATER HOSE

HINT:
Connect the outlet heater water hose using the same procedure as for the inlet heater water hose.



35. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A175964
  1. Align the connector with the pipe, then push in the connector to the pipe until it makes a "click" sound to connect the fuel tube sub-assembly to the fuel delivery pipe.

  1. Install the EFI fuel pipe clamp.



36. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    A177160
  1. Install the control cable to the transaxle with the bolt.



    A108714
  1. Install the control shaft lever with the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Install the control cable and a new clip to the bracket.



37. INSTALL NO. 1 INVERTER BRACKET


    A177161
  1. Install the 4 bolts and No. 1 inverter bracket.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }

  1. Install the harness clamp and hose clamp.



38. INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
  1. Temporarily install the compressor with motor assembly with the 3 bolts.



    A109432E01
  1. Install the compressor with motor assembly by tightening the 3 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Connect the 2 connectors.



39. INSTALL NO. 2 ENGINE MOUNTING BRACKET RH


40. INSTALL ENGINE MOUNTING CONTROL BRACKET


    A175878E01
  1. Install the 3 bolts and engine mounting control bracket.

    Torque:
    Bolt A:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }
    Bolt B:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



41. INSTALL ENGINE MOVING CONTROL ROD


    A175877E01
  1. Install the 2 bolts and engine moving control rod.

    Torque:
    Bolt A:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }
    Bolt B:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    HINT:
    First tighten bolt A.



42. INSTALL NO. 2 ENGINE MOUNTING STAY RH


    A175944
  1. Install the 2 bolts and No. 2 engine mounting stay RH.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



43. INSTALL AIR CLEANER BRACKET


    A108129
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



44. INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    A175945
  1. Install the 2 nuts and brake master cylinder reservoir.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the connector.



45. INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
Wear insulating gloves.



    A181830
  1. Install the inverter with converter assembly with the 2 nuts and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    1. Since the inverter with converter assembly is very heavy, 2 people are needed to remove the inverter with converter assembly. When removing the inverter with converter assembly, do not damage the parts around it.
    2. To prevent damage, do not hold the inverter with converter assembly by the connectors.
    3. To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.



46. INSTALL NO. 4 INVERTER BRACKET


    A181829
  1. Install the No. 4 inverter bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



47. INSTALL ENGINE ROOM RELAY BLOCK ASSEMBLY


    A181828
  1. Install the engine room relay block assembly.



48. REMOVE INVERTER COVER


    A181827
  1. Remove the 2 bolts and inverter cover from the inverter with converter assembly.



49. CONNECT NO. 3 FRAME WIRE

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the inverter with converter assembly is temporarily installed before working on the inverter with converter assembly (Click here).
  2. Do not allow any foreign objects or waterdrops to enter the inverter with converter assembly.



    A109800E01
  1. After connecting the connector, press the lever down to connect the No. 3 frame wire and install the bolt to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be sure to use a torque wrench to tighten the bolt.



    A108521
  1. Connect the No. 3 frame wire (high voltage cable of the rear motor (MGR)) with new 5 bolts to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure that the tightening torque is between 8.0 and 12 N*m (82 and 122kgf*cm, 6 and 9 ft.*lbf).



50. CONNECT MG ECU CONNECTOR

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the inverter with converter assembly is temporarily installed before working on the inverter with converter assembly (Click here).
  2. Do not allow any foreign objects or waterdrops to enter the inverter with converter assembly.



    A108518
  1. Connect the 2 connectors and 2 grommets to the inverter with converter assembly.



51. CONNECT HIGH VOLTAGE CABLE OF FRONT MOTOR

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the inverter with converter assembly is temporarily installed before working on the inverter with converter assembly (Click here).
  2. Do not allow any foreign objects or waterdrops to enter the inverter with converter assembly.



    A108520
  1. Connect the high voltage cable of the generator (MG1) with new 5 bolts to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure that the tightening torque is between 8.0 and 12 N*m (82 and 122kgf*cm, 6 and 9 ft.*lbf).



    A108519
  1. Connect the high voltage cable of the motor (MG2) with new 5 bolts to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure that the tightening torque is between 8.0 and 12 N*m (82 and 122kgf*cm, 6 and 9 ft.*lbf).



52. CONNECT NO. 4 ENGINE WIRE

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the inverter with converter assembly is temporarily installed before working on the inverter with converter assembly (Click here).
  2. Do not allow any foreign objects or waterdrops to enter the inverter with converter assembly.



    A177832
  1. Connect the No. 4 engine wire with the connector, clamp and grommet to the inverter with converter assembly.

  1. Connect the No. 4 engine wire with the bolt to the inverter with converter assembly.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



53. CHECK HIGH VOLTAGE CABLE CONNECTION

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the inverter with converter assembly is temporarily installed before working on the inverter with converter assembly (Click here).
  2. Do not allow any foreign objects or waterdrops to enter the inverter with converter assembly.



    A108527
  1. Check that each connector and terminal is firmly installed.

    NOTICE:
    1. Make sure that the connectors are fully engaged.
    2. Make sure that the bolts are fully tightened.



54. INSTALL INVERTER COVER


    A181826
  1. Install the inverter cover with the 12 bolts to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A175851
  1. Install the interlock bracket with the bolt to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



55. CONNECT WATER HOSE


    A181824
  1. Connect the water hose with the clamp to the inverter with converter assembly.



56. INSTALL INVERTER RESERVE TANK SUB-ASSEMBLY


    A108513
  1. Connect the 2 water hoses to the inverter reserve tank sub-assembly with the 2 clamps.



    A108512
  1. Install the inverter reserve tank with the 2 bolts to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



57. CONNECT NO. 2 ENGINE ROOM WIRE


    A175855
  1. Connect the No. 2 engine room wire with the nut.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the clamp.



    A175854
  1. Install the No. 2 relay block cover with the 4 claws.



    A175852
  1. Install the engine room relay block assembly.

  1. Install the relay block cover.



58. CONNECT NO. 1 CIRCUIT BREAKER SENSOR


    A177834
  1. Connect the No. 1 circuit breaker sensor connector.



59. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A173493
  1. Align the tab on the throttle body with the groove on the air cleaner hose and tighten the hose clamp.



    A173492
  1. Install the air cleaner case sub-assembly with the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A173491
  1. Connect the intake air flow meter connector.

  1. Connect the 2 wire harness clamps to the air cleaner case.



    A173490
  1. Connect the No. 1 ventilation hose.



60. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element to the air cleaner case.



    A175875
  1. Install the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



61. INSTALL BATTERY CARRIER SUB-ASSEMBLY


    A177162
  1. Install the 5 bolts and battery carrier.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



62. INSTALL SERVICE PLUG GRIP

NOTICE:
Before connecting the service plug, check that no parts and tools remain and that the high voltage terminals and connectors are connected securely.



    A176049
  1. Wear insulated gloves, then insert the service plug.

  1. Push down on the grip to lock.



    A175635
  1. Close the reclining hinge cover.

    NOTICE:
    Check that the 2 clips are securely connected to the battery carrier bracket (click sound).



    A175634
  1. Close the rear door scuff plate LH.

    NOTICE:
    Check that the 5 clips are securely connected to the battery carrier bracket (click sound).



63. INSTALL BATTERY
  1. Install the battery clamp and battery.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    6.4 N*m{ 65 kgf*cm , 56 in.*lbf }

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



64. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



65. ADD AND INSPECT HYBRID TRANSAXLE FLUID
  1. Add transaxle fluid.



    C173144E01
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Keep the fluid temperature at 5°C (41°F) or higher.
    2. Stop the vehicle on a flat road.
    3. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Using a socket hexagon wrench 10 mm, temporarily tighten the filler plug and gasket.

  1. Enter 2WD inspection mode (Click here).

  1. After waiting for 1 minute or more, stop the engine.

  1. Using a socket hexagon wrench 10 mm, remove the filler plug and gasket.

  1. Add transaxle fluid.



    C173144E01
  1. Check that the fluid surface is within 5 mm (0.20 in.) from the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Keep the fluid temperature at 5°C (41°F) or higher.
    2. Stop the vehicle on a flat road.
    3. Recheck the transaxle fluid level after driving when exchanging fluid.
    4. Insufficient or excessive amounts of transaxle fluid may be the cause of some trouble.

  1. Check for leaks if the fluid level is low.

  1. Using a socket hexagon wrench 10 mm, install the filler plug, and a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



66. ADD ENGINE OIL


67. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG) and push the Techstream main switch on.

      NOTICE:
      Do not start the engine.

    3. Select the following menu items: Power train / Engine / Active Test / Control the Fuel Pump Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, hybrid vehicle control ECU and wiring connector.

    5. Check that there are no fuel leaks anywhere on the fuel system after performing maintenance.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the Techstream from the DLC3.



68. ADD COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign objects.
  2. If the vehicle is driven with air in the inverter cooling system, the following DTCs may be set.

    DTC Code
    Detection Item
    P0A01-725
    Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
    P0A01-726
    Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
    P0A78-284
    Drive Motor "A" Inverter Performance
    P0A7A-322
    Generator Inverter Performance
    P0A93-346
    Inverter Cooling System Performance
    P0A94-553
    DC / DC Converter Performance
    P0AEE-276
    Motor Inverter Temperature Sensor "A" Circuit Range / Performance
    P0AEE-277
    Motor Inverter Temperature Sensor "A" Circuit Range / Performance
    P3221-314
    Generator Inverter Temperature Sensor Circuit Range / Performance
    P3221-315
    Generator Inverter Temperature Sensor Circuit Range / Performance
    P3226-562
    DC/DC Boost Converter Temperature Sensor
    P3226-563
    DC/DC Boost Converter Temperature Sensor



    A179308
  1. Loosen the bleeder plug shown in the illustration and connect a hose.

    NOTICE:
    Insert one end of the hose into the reserve tank.

  1. Add coolant to the reserve tank.



    C109303E01
  1. Add coolant until the level of coolant in the hose attached to the bleeder plug reaches the same level as the FULL line of the reserve tank.

    Coolant quantity:
    3.4 liter (3.6 US qts, 3.0 Imp. qts.)

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. On the Techstream, enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

    4. Keep the coolant at the FULL level in the reserve tank to compensate for the drop in coolant level when the air bleeds.

      Standard:
      Air bleeding from the coolant system is completed when the noise made by the water pump becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      Loud noise made by the water pump and poor circulation of coolant in the reserve tank indicates that there is air in the coolant system.

  1. When not using the Techstream:

    1. Turn the power switch on (READY). [*1]

    2. Turn the power switch off and add coolant to the FULL level because the coolant level drops as the air bleeds. [*2]

      NOTICE:
      1. Be sure to turn the power switch off before adding SLLC.
      2. Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

    3. Repeat steps [*1] and [*2] until air bleeding from the coolant system is completed.

      Standard:
      Air bleeding from the coolant system is completed when the noise made by the water pump becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      Loud noise made by the water pump and poor circulation of coolant in the reserve tank indicates that there is air in the coolant system.

  1. When the air is completely bled from the coolant system, tighten the plug.



    C109304
  1. Add coolant to the FULL mark of the reserve tank.



69. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 9 ft.*lbf }

  1. Loosen the air drain plug.



    A176032E01
  1. Install a vinyl tube to the vent tube located on the air drain plug.

  1. Fill the radiator with engine coolant until the vinyl tube is filled with the coolant.

  1. Tighten the air drain plug.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    CAUTION:
    1. Do not use an alcohol type coolant or plain water alone.
    2. The coolant must be mixed with plain water (preferably demineralized water).


    Coolant capacity:

    Condition
    Capacity
    w/ rear heater
    12.8 liters (13.5 US qts, 11.2 lmp.qts)
    w/o rear heater
    10.6 liters (11.2 US qts, 9.3 lmp.qts)

    HINT:
    1. Improper coolants may damage the engine cooling system.
    2. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. Use of coolant which includes more than 50% (freezing protection down to -35°C (-31°F)) or 60% (freezing protection down to -50°C (-58°F)) of ethylene-glycol is recommended but not more than 70%.
    4. Observe the coolant level inside the radiator by pressing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add the coolant.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Install the radiator cap securely.

  1. Fill the radiator reservoir tank with coolant.

  1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

    HINT:
    The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (C) through (K) and repeat the operation until the coolant level stays at the full level.

  1. Recheck the coolant level inside the radiator reservoir tank. If it is below the full level, add the coolant.



70. INSPECT FOR OIL LEAK


71. INSPECT FOR COOLANT LEAK (for Inverter)
  1. Remove the reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.



    A175857
  1. Install the radiator cap tester.

  1. Pump the radiator cap tester to 37 kPa (0.38 kgf/ cm2, 5.4 psi), and then check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator, water pump, inverter with converter, and hybrid vehicle transaxle assembly for leakage.

  1. Reinstall the reserve tank cap.



72. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A176028
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and cylinder head.



73. INSPECT FOR EXHAUST GAS LEAK


  1. Check that there are no exhaust gas leaks from the points (joints of the exhaust pipes and installation points of each sensor) shown in the illustration.


    A175970



74. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


75. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
(Click here)



76. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the 2 bolts and No. 2 engine under cover.



77. INSTALL FRONT FENDER APRON SEAL LH


    A109419
  1. Install the 2 bolts, clip and fender apron seal LH.



78. INSTALL FRONT FENDER APRON SEAL RH

HINT:
Perform the same procedure as above on the opposite side.



79. INSTALL FRONT FENDER LINER LH
  1. Install the front fender liner with the screw and clip.



80. INSTALL FRONT FENDER LINER RH

HINT:
Perform the same procedure as above on the opposite side.



81. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.



82. INSPECT STEERING WHEEL CENTER POINT


83. INSPECT IGNITION TIMING
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter DATA LIST MODE on the Techstream.

      Ignition timing:
      8 to 12° BTDC

      NOTICE:
      1. Turn all the electrical systems off.
      2. Inspect the engine idle speed with the cooling fan off.

      HINT:
      Refer to the Techstream operator's manual if you need help to select DATA LIST.

    3. Check that the ignition timing advances immediately when the engine speed is increased.



  1. When not using the Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting wrong terminals can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor is turned off.



    2. A108139
    3. Pull out the red-colored wire harness as shown in the illustration.

    4. Connect the tester terminal of the timing light to the red-colored wire.

      NOTICE:
      Use a timing light which detects the first signal.

    5. Inspect ignition timing at idle.

      Ignition timing:
      8 to 12° BTDC

      NOTICE:
      When checking the ignition timing, the transmission is in neutral.

      HINT:
      Run the engine at 1,000 to 1,300 rpm for 5 seconds, check that the engine rpm returns to idle speed.

    6. Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.

    7. Inspect ignition timing at idle.

      Ignition timing:
      7 to 24° BTDC

    8. Confirm that the ignition timing advances when the engine rpm is increased.

    9. Remove the timing light.



84. INSPECT ENGINE IDLE SPEED
  1. Set the vehicle to inspection mode (Click here).

  1. Warm up the engine.

  1. Connect the Techstream to the DLC3.

  1. Enter DATA LIST MODE on the Techstream.

    Idle speed:
    850 to 950 rpm.

    NOTICE:
    1. When checking the idle speed, the transmission is in neutral.
    2. Check the idle speed with the cooling fan off.
    3. Switch off all accessories and air conditioning before connecting the Techstream.

    HINT:
    Refer to the Techstream operator's manual for further details.



85. INSPECT CO/HC
  1. Set the vehicle to inspection mode (Click here).

  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.



    A175874
  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idling.

  1. Check CO/HC concentration at idle and/or 2,500 rpm.

    HINT:
    When doing the 2 mode (idle and 2,500 rpm) test, the measuring procedures are prescribed by the applicable local regulations.

    If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check heated oxygen sensor operation (Click here).

    2. Check heated air fuel ratio sensor operation (Click here).

    3. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Defective water temperature sensor
        3. Defective mass air-flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor



86. CHECK ABS SPEED SENSOR SIGNAL

HINT:
(Click here)



87. INSTALL NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Fit the clips and install the No. 2 engine room side cover LH.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.



88. INSTALL COOL AIR INTAKE DUCT SEAL
  1. Install the cool air intake duct seal with the 11 clips.



89. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175030E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C175029
  1. Engage the 4 clamps.



90. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



91. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



92. INSTALL HOOD TO COWL TOP SEAL


    E150148
  1. Engage the 8 clips and install the hood to cowl top seal.



93. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



94. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.