Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095459 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
·

Power window regulator master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Power window regulator motor assembly (for front passenger door)

·

Power window regulator motor assembly (for rear RH door)*1

·

Power window regulator motor assembly (for rear LH door)*1

·

Sliding roof ECU (sliding roof drive gear sub-assembly)*2

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

A/C fuse

·

P/W F/L fuse

·

P/W F/R fuse

·

P/W R/L fuse*1

·

P/W R/R fuse*1

·

S/ROOF fuse*2



*1: for Models with Jam Protection Function on 4 Windows

*2: w/ Sliding Roof System


WIRING DIAGRAM

for LHD


B365177
2.042,0.385 2.854,0.625 0.813,0.24 10 false from Battery 1.375,2.396 2.958,2.969 1.583,0.573 10 false Power Window Regulator Master Switch Assembly 0.74,1.385 1.063,1.656 0.323,0.271 10 false A/C 1.385,2.208 2.427,2.427 1.042,0.219 10 false I7 2.74,1.635 3.031,1.833 0.292,0.198 10 false 17 2.74,1.115 3.094,1.313 0.354,0.198 10 false 16 2.375,1.26 2.771,1.51 0.396,0.25 10 false LIN2 2.375,1.781 2.76,2 0.385,0.219 10 false LIN1 3.896,4.146 6.469,4.542 2.573,0.396 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 1.51,1.813 1.885,1.99 0.375,0.177 10 false GND 4.156,2.125 6.115,2.479 1.958,0.354 10 false Power Window Regulator Motor Assembly (for Driver Door) 1.531,1.26 1.75,1.563 0.219,0.302 10 false B 1.26,1.135 1.615,1.333 0.354,0.198 10 false 11 1.271,1.688 1.625,1.885 0.354,0.198 10 false 12 4.51,1.25 4.896,1.469 0.385,0.219 10 false LIN 2.448,4.073 2.833,4.292 0.385,0.219 10 false LIN 4.5,5.729 4.885,5.948 0.385,0.219 10 false LIN 4.302,1.104 4.594,1.302 0.292,0.198 10 false 9 5.521,1.24 5.813,1.438 0.292,0.198 10 false B 5.75,1.563 6.042,1.76 0.292,0.198 10 false 1 4.156,1.958 4.969,2.198 0.813,0.24 10 false I4 5.344,1.677 5.76,1.875 0.417,0.198 10 false GND 5.74,1.115 6.031,1.313 0.292,0.198 10 false 2 4.323,3.271 4.615,3.469 0.292,0.198 10 false 9 4.313,5.552 4.604,5.75 0.292,0.198 10 false 9 5.74,3.115 6.031,3.313 0.292,0.198 10 false 2 5.74,3.583 6.031,3.781 0.292,0.198 10 false 1 5.729,5.854 6.021,6.052 0.292,0.198 10 false 1 5.74,5.417 6.031,5.615 0.292,0.198 10 false 2 4.51,3.427 4.896,3.646 0.385,0.219 10 false LIN 1.531,3.875 1.917,4.094 0.385,0.219 10 false B 1.531,4.313 1.948,4.51 0.417,0.198 10 false GND 5.333,3.688 5.75,3.885 0.417,0.198 10 false GND 5.323,5.958 5.74,6.156 0.417,0.198 10 false GND 5.5,3.26 5.885,3.479 0.385,0.219 10 false B 5.531,5.552 5.917,5.771 0.385,0.219 10 false B 2.76,3.854 3.052,4.052 0.292,0.198 10 false 9 1.313,3.698 1.604,3.896 0.292,0.198 10 false 2 1.313,4.156 1.604,4.354 0.292,0.198 10 false 1 3.906,3.969 4.719,4.208 0.813,0.24 10 false H5 6.031,1.385 6.625,1.729 0.594,0.344 10 false P/W F/L 1.146,4.802 3.104,5.208 1.958,0.406 10 false Power Window Regulator Motor Assembly (for Rear LH Door) 1.146,4.646 1.958,4.885 0.813,0.24 10 false K2 6.052,3.417 6.656,3.656 0.604,0.24 10 false P/W F/R 0.594,4.031 1.198,4.271 0.604,0.24 10 false P/W R/L 6.042,5.698 6.646,5.938 0.604,0.24 10 false P/W R/R 4.177,6.479 6.135,6.885 1.958,0.406 10 false Power Window Regulator Motor Assembly (for Rear RH Door) 4.177,6.323 4.99,6.563 0.813,0.24 10 false J2 0.49,7.615 1.646,8.177 1.156,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 1.781,7.438 3.427,7.844 1.646,0.406 10 false Instrument Panel Junction Block Assembly 3.521,7.198 4.333,7.438 0.813,0.24 10 false A 1.75,6.844 2.563,7.083 0.813,0.24 10 false MB 2.75,6.406 3.563,6.646 0.813,0.24 10 false 4H 2.76,6.844 3.573,7.083 0.813,0.24 10 false 4D 1.771,6.656 2.583,6.896 0.813,0.24 10 false 16 2.771,6.219 3.583,6.458 0.813,0.24 10 false 35 2.76,6.646 3.573,6.885 0.813,0.24 10 false 25 4.094,8.438 5.844,8.708 1.75,0.271 10 false : LIN Communication Line 1.354,6.844 1.74,7.063 0.385,0.219 10 false LIN2 0.198,5.042 1.01,5.281 0.813,0.24 10 false B 6.844,6.354 7,6.573 0.156,0.219 10 false C

B365186
4.01,1.792 5.958,2.188 1.948,0.396 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)* 0.854,2.333 4.521,2.531 3.667,0.198 10 false : LIN Communication Line 3.385,0.229 3.542,0.427 0.156,0.198 10 false A 5.906,1.198 6.479,1.417 0.573,0.219 10 false S/ROOF 4.354,1.229 4.927,1.448 0.573,0.219 10 false MPX1 5.406,1.073 5.667,1.271 0.26,0.198 10 false B 5.406,1.438 5.625,1.656 0.219,0.219 10 false E 4.115,1.073 4.688,1.292 0.573,0.219 10 false 11 5.604,0.948 6.177,1.167 0.573,0.219 10 false 8 5.594,1.313 6.167,1.531 0.573,0.219 10 false 12 5.167,2.417 6.896,2.677 1.729,0.26 10 false *: w/ Sliding Roof System 4.01,1.625 4.583,1.844 0.573,0.219 10 false S5 6.708,0.323 6.865,0.521 0.156,0.198 10 false B


for RHD


B365378
2.073,0.375 3.052,0.729 0.979,0.354 10 false from Battery 1.313,2.344 2.875,2.865 1.563,0.521 10 false Power Window Regulator Master Switch Assembly 4.208,2.167 6.167,2.594 1.958,0.427 10 false Power Window Regulator Motor Assembly (for Driver Door) 1.125,4.833 3.063,5.24 1.938,0.406 10 false Power Window Regulator Motor Assembly (for Rear LH Door)*1 3.885,4.25 6.458,4.656 2.573,0.406 10 false Power Window Regulator Motor Assembly (for Front Passenger Door) 4.135,6.479 6.083,6.927 1.948,0.448 10 false Power Window Regulator Motor Assembly (for Rear RH Door)*1 0.51,7.604 1.677,8.177 1.167,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 4.208,2.01 5.188,2.365 0.979,0.354 10 false H4 1.313,2.167 2.292,2.521 0.979,0.354 10 false H7*1, H6*2 1.125,4.656 2.104,5.01 0.979,0.354 10 false K2 3.896,4.094 4.875,4.448 0.979,0.354 10 false I5 4.125,6.313 5.104,6.667 0.979,0.354 10 false J2 1.354,6.844 2.333,7.198 0.979,0.354 10 false LIN2 1.792,7.427 3.396,7.823 1.604,0.396 10 false Instrument Panel Junction Block Assembly 4.51,5.729 5.49,6.083 0.979,0.354 10 false LIN 2.438,4.063 3.417,4.417 0.979,0.354 10 false LIN 4.51,3.438 5.49,3.792 0.979,0.354 10 false LIN 2.365,1.802 3.344,2.156 0.979,0.354 10 false LIN1 2.365,1.26 3.344,1.615 0.979,0.354 10 false LIN2 4.51,1.281 5.49,1.635 0.979,0.354 10 false LIN 1.521,1.24 2.5,1.594 0.979,0.354 10 false B 1.51,1.823 2.49,2.177 0.979,0.354 10 false GND 5.542,1.25 5.729,1.458 0.188,0.208 10 false B 5.354,1.688 5.76,1.927 0.406,0.24 10 false GND 1.531,3.885 1.719,4.094 0.188,0.208 10 false B 5.521,3.26 5.708,3.469 0.188,0.208 10 false B 5.531,5.552 5.719,5.76 0.188,0.208 10 false B 5.344,3.688 5.75,3.927 0.406,0.24 10 false GND 5.344,5.969 5.75,6.208 0.406,0.24 10 false GND 1.521,4.313 1.927,4.552 0.406,0.24 10 false GND 6.031,1.375 6.677,1.615 0.646,0.24 10 false P/W F/R 0.74,1.385 1.385,1.625 0.646,0.24 10 false A/C 0.583,4.031 1.229,4.271 0.646,0.24 10 false P/W R/L 6.052,3.396 6.698,3.635 0.646,0.24 10 false P/W F/L 6.031,5.688 6.677,5.927 0.646,0.24 10 false P/W R/R 1.323,3.75 1.51,3.958 0.188,0.208 10 false 2 1.313,4.188 1.5,4.396 0.188,0.208 10 false 1 2.75,3.896 2.938,4.104 0.188,0.208 10 false 9 4.323,3.292 4.51,3.5 0.188,0.208 10 false 9 4.313,1.115 4.5,1.323 0.188,0.208 10 false 9 4.333,5.563 4.521,5.771 0.188,0.208 10 false 9 5.74,1.583 5.927,1.792 0.188,0.208 10 false 1 5.74,3.594 5.927,3.802 0.188,0.208 10 false 1 5.74,5.875 5.927,6.083 0.188,0.208 10 false 1 5.729,1.146 5.917,1.354 0.188,0.208 10 false 2 5.74,3.156 5.927,3.365 0.188,0.208 10 false 2 5.74,5.438 5.927,5.646 0.188,0.208 10 false 2 2.771,6.219 2.958,6.427 0.188,0.208 10 false 35 2.771,6.667 2.958,6.875 0.188,0.208 10 false 25 1.76,6.667 1.948,6.875 0.188,0.208 10 false 16 3.521,7.198 3.708,7.406 0.188,0.208 10 false A 6.854,6.333 7.042,6.542 0.188,0.208 10 false B 1.74,6.854 2.219,7.229 0.479,0.375 10 false MB 2.76,6.844 3.135,7.135 0.375,0.292 10 false 4D 2.76,6.406 3,6.635 0.24,0.229 10 false 4H 3.49,7.74 7.135,7.979 3.646,0.24 10 false *1: for Models with Jam Protection Function on 4 Windows 3.49,8.073 7.135,8.385 3.646,0.313 10 false *2: for Models with Jam Protection Function on 2 Windows 4.094,8.438 6.031,8.635 1.938,0.198 10 false : LIN Communication Line 2.74,1.125 3.052,1.375 0.313,0.25 10 false 7*2 1.219,1.156 1.594,1.458 0.375,0.302 10 false 3*2 1.146,1 1.531,1.219 0.385,0.219 10 false 11*1 1.125,1.563 1.5,1.823 0.375,0.26 10 false 12*1 1.198,1.708 1.448,1.969 0.25,0.26 10 false 1*2 2.74,1.656 3.094,1.958 0.354,0.302 10 false 6*2 2.729,1.5 3.156,1.792 0.427,0.292 10 false 17*1 2.708,0.969 3.125,1.219 0.417,0.25 10 false 16*1

B365186
4.021,1.792 5.969,2.188 1.948,0.396 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)* 0.854,2.333 4.521,2.531 3.667,0.198 10 false : LIN Communication Line 3.385,0.229 3.542,0.427 0.156,0.198 10 false A 5.906,1.198 6.479,1.417 0.573,0.219 10 false S/ROOF 4.354,1.229 4.927,1.448 0.573,0.219 10 false MPX1 5.406,1.073 5.667,1.271 0.26,0.198 10 false B 5.406,1.438 5.625,1.656 0.219,0.219 10 false E 4.115,1.073 4.688,1.292 0.573,0.219 10 false 11 5.604,0.948 6.177,1.167 0.573,0.219 10 false 8 5.594,1.313 6.167,1.531 0.573,0.219 10 false 12 5.167,2.417 6.896,2.677 1.729,0.26 10 false *: w/ Sliding Roof System 4.01,1.625 4.583,1.844 0.573,0.219 10 false S5 6.708,0.323 6.865,0.521 0.156,0.198 10 false B


CAUTION / NOTICE / HINT

NOTICE:
·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>INITIALIZATION

·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (w/ Sliding Roof System).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

Before performing the inspection, check that DTC B1206, B1273, B2321, B2322, B2323 or B2324 is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Models with Jam Protection Function on 4 Windows A
for Models with Jam Protection Function on 2 Windows B



A

2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

12.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B365181
1.156,1.854 1.49,1.854 1.49,1.854 1.49,1.354 false 2.083,1.854 1.667,1.854 1.667,1.854 1.667,1.354 false 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 0.844,1.781 1.458,1.979 0.615,0.198 10 false LIN1 2.146,1.771 2.76,1.969 0.615,0.198 10 false LIN2
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (LIN2) - 17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
a.

for LHD

i.

Disconnect the I4 power window regulator motor assembly (for driver door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
I7-16 (LIN2) - I4-9 (LIN) Ignition switch off Below 1 Ω
I7-16 (LIN2) or I4-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher




b.

for RHD

i.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
H7-16 (LIN2) - H4-9 (LIN) Ignition switch off Below 1 Ω
H7-16 (LIN2) or H4-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B365184
1.833,1.583 2.25,1.833 0.417,0.25 5.083,1.583 5.5,1.833 0.417,0.25 3.5,0.25 3.917,0.5 0.417,0.25 3.792,1.271 3.792,1.021 false 0.26,0.188 0.573,0.385 0.313,0.198 10 false *a 3.604,0.302 3.917,0.5 0.313,0.198 10 false MB 5.219,1.625 5.531,1.823 0.313,0.198 10 false 4D 1.958,1.625 2.271,1.823 0.313,0.198 10 false 4H 3.677,1.313 4.292,1.51 0.615,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - MB-16 (LIN2) Always Below 1 Ω
4H-35 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
a.

for LHD

i.

Disconnect the H5 power window regulator motor assembly (for front passenger door) connector.


ii.

Disconnect the K2 power window regulator motor assembly (for rear LH door) connector.


iii.

Disconnect the J2 power window regulator motor assembly (for rear RH door) connector.


iv.

Disconnect the I7 power window regulator master switch assembly connector.


v.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*

*: w/ Sliding Roof System



vi.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - I7-17 (LIN1) Ignition switch off Below 1 Ω
4D-25 - S5-11 (MPX1)* Ignition switch off Below 1 Ω
4D-25 - H5-9 (LIN) Ignition switch off Below 1 Ω
4D-25 - J2-9 (LIN) Ignition switch off Below 1 Ω
4H-35 - K2-9 (LIN) Ignition switch off Below 1 Ω
I7-17 (LIN1) - Body ground Ignition switch off 10 kΩ or higher
S5-11 (MPX1) - Body ground* Ignition switch off 10 kΩ or higher
4D-25 - Body ground Ignition switch off 10 kΩ or higher
4H-35 - Body ground Ignition switch off 10 kΩ or higher
H5-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher
J2-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher
K2-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher


*: w/ Sliding Roof System




b.

for RHD

i.

Disconnect the I5 power window regulator motor assembly (for front passenger door) connector.


ii.

Disconnect the K2 power window regulator motor assembly (for rear LH door) connector.


iii.

Disconnect the J2 power window regulator motor assembly (for rear RH door) connector.


iv.

Disconnect the H7 power window regulator master switch assembly connector.


v.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*

*: w/ Sliding Roof System



vi.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - H7-17 (LIN1) Ignition switch off Below 1 Ω
4D-25 - S5-11 (MPX1)* Ignition switch off Below 1 Ω
4D-25 - J2-9 (LIN) Ignition switch off Below 1 Ω
4D-25 - I5-9 (LIN) Ignition switch off Below 1 Ω
4H-35 - K2-9 (LIN) Ignition switch off Below 1 Ω
H7-17 (LIN1) - Body ground Ignition switch off 10 kΩ or higher
S5-11 (MPX1) - Body ground* Ignition switch off 10 kΩ or higher
4D-25 - Body ground Ignition switch off 10 kΩ or higher
4H-35 - Body ground Ignition switch off 10 kΩ or higher
J2-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher
I5-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher
K2-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher


*: w/ Sliding Roof System




Result:
Proceed to
OK
NG



OK

6.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)
a.

for LHD

i.

Reconnect the 4D and 4H instrument panel junction block assembly connectors.


ii.

Reconnect the I4 power window regulator motor assembly (for driver door) connector.


iii.

Reconnect the H5 power window regulator motor assembly (for front passenger door) connector.


iv.

Reconnect the J2 power window regulator motor assembly (for rear RH door) connector.


v.

Reconnect the I7 power window regulator master switch assembly connector.


vi.

Reconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*

*: w/ Sliding Roof System



vii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

viii.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the 4D and 4H instrument panel junction block assembly connectors.


ii.

Reconnect the H4 power window regulator motor assembly (for driver door) connector.


iii.

Reconnect the I5 power window regulator motor assembly (for front passenger door) connector.


iv.

Reconnect the J2 power window regulator motor assembly (for rear RH door) connector.


v.

Reconnect the H7 power window regulator master switch assembly connector.


vi.

Reconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*

*: w/ Sliding Roof System



vii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

viii.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

7.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

7.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

for LHD

i.

Reconnect the K2 power window regulator motor assembly (for rear LH door) connector.


ii.

Disconnect the I7 power window regulator master switch assembly connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the K2 power window regulator motor assembly (for rear LH door) connector.


ii.

Disconnect the H7 power window regulator master switch assembly connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

8.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

8.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)
a.

for LHD

i.

Reconnect the I7 power window regulator master switch assembly connector.


ii.

Disconnect the J2 power window regulator motor assembly (for rear RH door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the H7 power window regulator master switch assembly connector.


ii.

Disconnect the J2 power window regulator motor assembly (for rear RH door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

9.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

9.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)
a.

for LHD

i.

Reconnect the J2 power window regulator motor assembly (for rear RH door) connector.


ii.

Disconnect the I4 power window regulator motor assembly (for driver door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the J2 power window regulator motor assembly (for rear RH door) connector.


ii.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

10.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

10.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)
a.

for LHD

i.

Reconnect the I4 power window regulator motor assembly (for driver door) connector.


ii.

Disconnect the H5 power window regulator motor assembly (for front passenger door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the H4 power window regulator motor assembly (for driver door) connector.


ii.

Disconnect the I5 power window regulator motor assembly (for front passenger door) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

11.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

11.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

for LHD

i.

Reconnect the H5 power window regulator motor assembly (for front passenger door) connector.


ii.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


b.

for RHD

i.

Reconnect the I5 power window regulator motor assembly (for front passenger door) connector.


ii.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


iii.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

iv.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123


Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

12.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B365182
1.063,0.281 1.396,0.281 1.396,0.281 1.396,1.031 false 1.885,0.281 1.552,0.281 1.552,0.281 1.552,1.031 false 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.74,0.208 1.052,0.406 0.313,0.198 10 false LIN2 1.958,0.198 2.271,0.396 0.313,0.198 10 false LIN1
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LIN2) - 6 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
a.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
H6-7 (LIN2) - H4-9 (LIN) Ignition switch off Below 1 Ω
H6-7 (LIN2) or H4-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B345099
2.083,0.917 2.417,1.167 0.333,0.25 5.417,0.667 5.75,0.917 0.333,0.25 2,2 2.198,1.583 false 2.167,0.969 2.479,1.167 0.313,0.198 10 false MB 0.354,0.333 0.667,0.531 0.313,0.198 10 false *a 5.51,0.708 5.823,0.906 0.313,0.198 10 false 4D 1.854,2.052 2.167,2.25 0.313,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
a.

Disconnect the I5 power window regulator motor assembly (for front passenger door) connector.


b.

Disconnect the H6 power window regulator master switch assembly connector.


c.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*

*: w/ Sliding Roof System



d.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - H6-6 (LIN1) Ignition switch off Below 1 Ω
4D-25 - S5-11 (MPX1)* Ignition switch off Below 1 Ω
4D-25 - I5-9 (LIN) Ignition switch off Below 1 Ω
H6-6 (LIN1) - Body ground Ignition switch off 10 kΩ or higher
S5-11 (MPX1) - Body ground* Ignition switch off 10 kΩ or higher
4D-25 - Body ground Ignition switch off 10 kΩ or higher
I5-9 (LIN) - Body ground Ignition switch off 10 kΩ or higher


*: w/ Sliding Roof System



Result:
Proceed to
OK
NG



OK

16.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Reconnect the 4D instrument panel junction block assembly connector.


b.

Reconnect the H4 power window regulator motor assembly (for driver door) connector.


c.

Reconnect the I5 power window regulator motor assembly (for front passenger door) connector.


d.

Reconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.*

*: w/ Sliding Roof System



e.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

f.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

17.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

17.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)
a.

Reconnect the H6 power window regulator master switch assembly connector.


b.

Disconnect the H4 power window regulator motor assembly (for driver door) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

18.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

18.CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)
a.

Reconnect the H4 power window regulator motor assembly (for driver door) connector.


b.

Disconnect the I5 power window regulator motor assembly (for front passenger door) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Sliding Roof System) A
DTC B2325 is output (w/o Sliding Roof System) B
DTC B2325 is not output C



A

19.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

19.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Reconnect the I5 power window regulator motor assembly (for front passenger door) connector.


b.

Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

d.

After 10 seconds have elapsed, check if the same DTC is output again.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)