Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0104  Lost Communication with Driving Support ECU  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0104 Lost Communication with Driving Support ECU No communication from the driving support ECU assembly continues.
·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly


HINT:

Network gateway ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 2.



HINT:

This diagnosis procedure is for when DTC U0104 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM

C294978
1.99,1.125 2.677,0.125 2.677,0.125 2.823,0.125 false 4.667,1.125 5.354,0.125 5.354,0.125 5.5,0.125 false 0.042,0.042 1.875,0.281 1.833,0.24 12 false Sub Bus 2: 1.125,5.063 5.104,5.26 3.979,0.198 10 false : CAN Main Bus Line (CANH) 1.125,5.385 5.104,5.583 3.979,0.198 10 false : CAN Main Bus Line (CANL) 4.26,5.063 6.115,5.417 1.854,0.354 10 false : CAN Branch Line (CANH) 4.26,5.396 6.104,5.667 1.844,0.271 10 false : CAN Branch Line (CANL) 0.625,4.083 2.458,4.281 1.833,0.198 10 false Trouble Area 1.688,3.969 2.531,4.281 0.844,0.313 10 false IG1 NO. 3 2.823,3.813 3.135,4.01 0.313,0.198 10 false B 3.042,3.49 3.656,3.688 0.615,0.198 10 false CA2H 3.563,3.49 4.177,3.688 0.615,0.198 10 false CA2L 3.896,3.781 4.354,3.979 0.458,0.198 10 false GND 2.677,4.323 4.76,4.573 2.083,0.25 10 false Driving Support ECU Assembly 2.396,4.323 2.708,4.521 0.313,0.198 10 false F84 3.135,3.292 3.448,3.49 0.313,0.198 10 false 39 3.729,3.292 4.042,3.49 0.313,0.198 10 false 17 4.24,3.688 4.552,3.885 0.313,0.198 10 false 25 2.615,3.708 2.927,3.906 0.313,0.198 10 false 30 2.906,0.031 4.146,1.01 1.24,0.979 10 false No. 1 CAN Junction Connector 5.573,0.021 6.813,1 1.24,0.979 10 false No. 2 CAN Junction Connector 0.313,2.635 1.448,3.427 1.135,0.792 10 false Network Gateway ECU 5.677,2.688 7.115,3.031 1.438,0.344 10 false CAN Junction Terminal 0.708,2.021 1.479,2.219 0.771,0.198 10 false 120 Ω 6.167,2.021 6.938,2.219 0.771,0.198 10 false 120 Ω

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 15.2 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for 1 second or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
Body Electrical > Gateway > Trouble Codes
50001 150
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.



Result:
Result Proceed to
DTC U1002 is not output from network gateway ECU (GTS display: Gateway) A
DTC U1002 is output from network gateway ECU (GTS display: Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 2 LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 2 LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F84 driving support ECU assembly connector.


c.
C292382
0.615,0.365 0.99,0.698 0.375,0.333 2.771,1.375 2.615,0.542 2.615,0.542 2.542,0.542 true 2.323,2 2.438,2 2.438,2 2.74,1.531 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.688,0.427 1,0.625 0.313,0.198 10 false F84 2.177,0.458 2.792,0.656 0.615,0.198 10 false CA2L 1.917,1.906 2.531,2.104 0.615,0.198 10 false CA2H
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-39 (CA2H) - F84-17 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C292382
0.615,0.365 0.99,0.698 0.375,0.333 0.927,2.01 1.042,2.01 1.042,2.01 1.344,1.542 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.688,0.427 1,0.625 0.313,0.198 10 false F84 0.573,1.917 1.188,2.115 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F84-25 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C292382
0.615,0.365 0.99,0.698 0.375,0.333 1.375,2.01 1.49,2.01 1.49,2.01 1.792,1.542 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 0.688,0.417 1,0.615 0.313,0.198 10 false F84 1.25,1.917 1.865,2.115 0.615,0.198 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F84-30 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)